SAAB WIS ONLINE

OPERATION

OPERATION

READ DIAGNOSTIC TROUBLE CODE (DTC)

Prepare the Vehicle Diagnostic Interface kit.

Connect the diagnosis cable to Vehicle Diagnostic Interface.

Connect the Vehicle Diagnostic Interface to data link connector.

Data link connector located in the lower portion of instrument panel (on driver’s side).


Connect the diagnosis cable to data link connector.

Note

Do not connect scan tools except for Vehicle Diagnostic Interface and OBD-II general scan tool.


Turn the ignition switch to ON (engine OFF), and start the Vehicle Diagnostic Interface.

On the «Main Menu» display screen, select the {Each System Check}.

On the «System Selection Menu» display screen, select the {Transmission Control System}.

Select the {OK} after the information of transmission type is displayed.

On the «Transmission Diagnosis» display screen, select the {DTC Display}.

On the «DTC Display» display screen, select the {Memorized DTC}.

Note
• For detailed operation procedure, refer to the Vehicle Diagnostic Interface OPERATION MANUAL.

• For details concerning the DTC, refer to the List of Diagnostic Trouble Code (DTC).


READ CURRENT DATA

On the «Main Menu» display screen, select the {Each System Check}.

On the «System Selection Menu» display screen, select the {Transmission Control System}.

Select the {OK} after the information of transmission type is displayed.

On the «Transmission Diagnosis» display screen, select the {Current Data Display & Save}.

On the «Data Display Menu» display screen, select the {Data Display}.

Using the scroll key, move the display screen up or down until desired data is shown.


• A list of the support data is shown in the following table.

Contents Display Unit of measure
Battery voltage

Battery Voltage

V

Rear vehicle speed sensor signal

Rear Wheel Speed

km/h or MPH

Front vehicle speed sensor signal

Front Wheel Speed

km/h or MPH

Engine speed signal

Engine Speed

rpm

Automatic transmission fluid temperature signal

ATF Temp.

°C or °F

Throttle position signal

Throttle Sensor Voltage

V

Gear position

Gear Position

—

Line pressure control duty ratio

Line Pressure Duty Ratio

%

Lock up clutch control duty ratio

Lock Up Duty Ratio

%

Transfer clutch control duty ratio (AWD model)

Transfer Duty Ratio

%

Power supply for throttle position sensor

Throttle Sensor Power

V

Torque converter turbine speed signal

Turbine Revolution Speed

rpm

2-4 brake timing pressure control duty ratio

Brake Clutch Duty Ratio

%

Mass air flow sensor signal

Air Flow Sensor Voltage

V

Stop light switch signal

Stop Light Switch

ON or OFF

Anti lock brake system signal

ABS Signal

ON or OFF

Cruise control system signal

Cruise Control Signal

ON or OFF

Parking range signal

P Range Signal

ON or OFF

Neutral range signal

N Range Signal

ON or OFF

Reverse range signal

R Range Signal

ON or OFF

Drive range signal

D Range Signal

ON or OFF

3rd range signal

3rd Range Signal

ON or OFF

2nd range signal

2nd Range Signal

ON or OFF

1st range signal

1st Range Signal

ON or OFF

Shift control solenoid 1

Shift Solenoid #1

ON or OFF

Shift control solenoid 2

Shift Solenoid #2

ON or OFF

Torque control output signal #1

Torque Control Signal 1

ON or OFF

Torque control output signal #2

Torque Control Signal 2

ON or OFF

Torque control cut signal

Torque Control Cut Sig.

ON or OFF

2-4 brake timing control solenoid valve

2-4 Brake Timing Sol.

ON or OFF

Low clutch timing control solenoid valve

Low Clutch Timing Sol.

ON or OFF

Automatic transmission diagnosis indicator lamp

Diagnosis Lamp

ON or OFF

Automatic transmission fluid temperature lamp

ATF Temperature Lamp

ON or OFF



Note

For detailed operation procedure, refer to the Vehicle Diagnostic Interface OPERATION MANUAL.



CLEAR MEMORY MODE

On the «Main Menu» display screen, select the {2. Each System Check}.

On the «System Selection Menu» display screen, select the {Transmission Control System}.

Select the {OK} after the information of transmission type is displayed.

On the «Transmission Diagnosis» display screen, select the {Clear Memory}.

When the “Done” is shown on display screen, turn the Vehicle Diagnostic Interface and ignition switch to OFF.

Note

For detailed operation procedure, refer to the Vehicle Diagnostic Interface OPERATION MANUAL.