87 81 841 Silicone flange sealant
|
|
87 81 841 Silicone flange sealant
|
Loctite Ultra Grey 5699. Elastic joint compound. 300 ml cartridge.
Replaces 44 91 056 for groove in metal gasket between engine and gearbox Saab 90/99/900 -M93, -M94 Convertible and Saab 9000 2.0 with groove in the oil sump seal surface. AW-transmission housings.
1
No restrictions apply when transporting this product.
|
Material safety data sheet
|
|
1.
|
IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING
Product code
|
0391735
|
Product name
|
Ultra Grey 5999
Superflex 5699 HB
|
Manufacturer - supplier
|
Loctite Sweden AB
Box 8823
SE-402 71 GÖTEBORG
Tel: +46 31 7505400
Fax: +46 31 7505391
Tel (emergencies): +353-1-4599301 / +353-87-2629625 / +353-1-4046444
|
|
|
2.
|
COMPOSITION/INFORMATION ON INGREDIENTS
Product type
|
Silicone sealant
|
Ingredient
|
CAS-no.
|
Conc.
|
R-phrases
|
Classification
|
Oximo silane
|
|
3.00 - 7.00
|
R36
|
|
Ketoximo crosslinker
|
|
0.10 - 1.00
|
R11, R36/37/38
|
|
Polydimethylsiloxane hydroxy terminated
|
63148-60-7
|
30.00 - 50.00
|
|
|
Key
|
FB/FH/FM = Hazard code for fire/health/environment
T+ = Very toxic
T = Toxic
C = Corrosive
Xn = Harmful
Xi = Irritant
V = Moderately harmful
IK = Not subject to labelling
E = Explosive
O = Oxidizing
F+ = Extremely flammable
F = Highly flammable
N = Dangerous for the environment
|
|
|
3.
|
HAZARDS IDENTIFICATION
Oxime curing silicones release vapours of methyl ethyl ketoxime in contact with moisture. Methyl ethyl ketoxime is irritating to the eyes and respiratory system.
|
|
4.
|
FIRST AID MEASURES
Inhalation
|
Remove affected person to fresh air. By-products released during polymerisation may cause irritation to respiratory system.
|
Skin
|
Wash immediately with soap and water.
|
Eyes
|
Flush eyes immediately with plenty of water for at least 15 minutes. Volatile by-products released during polymerisation may cause irritation to eyes.
|
Ingestion
|
Rinse mouth with water then give plenty of water to drink. Do not induce vomiting.
|
|
|
5.
|
FIRE-FIGHTING MEASURES
Suitable extinguishing media
|
Non-flammable product (flash point >100°C). If product is involved in fire extinguish with dry powder, foam or carbon dioxide.
|
Fire/Explosions risks
|
No unusual fire hazards.
|
|
|
6.
|
SPILLAGE/ACCIDENTAL RELEASE MEASURES
Personal precautions
|
Ventilate area. Silicones release by-products in contact with moisture which are irritating to eyes and respiratory system.
|
Methods for cleaning up
|
Wash spillage site thoroughly with soap and water or detergent solution.
|
|
|
7.
|
HANDLING AND STORAGE
Advice for safe handling
|
Use in a well-ventilated area. Vapours should be extracted to avoid inhalation.
|
Storage instructions
|
No special storage conditions required. Keep in a cool, well-ventilated area.
|
|
|
8.
|
EXPOSURE CONTROLS/PERSONAL PROTECTION
Skin protection
|
In case of repeated or prolonged skin contact, wear suitable gloves made of polyethene, natural rubber or similar ester-resistant material.
|
Hygiene
|
Good industrial hygiene practices should be observed.
|
|
|
9.
|
PHYSICAL AND CHEMICAL PROPERTIES
Form/state
|
Paste
|
Odour
|
Mild, characteristic
|
Colour
|
Grey
|
Boiling point (°C)
|
>200
|
Solubility in water
|
Insoluble
|
Solubility in acetone
|
Partially soluble
|
Density
|
1.44 - 1.49 kg/m
3
|
Vapour pressure
|
Less than 0.1 mm Hg at 20°C
|
|
|
10.
|
STABILITY AND REACTIVITY
Stability
|
Relatively stable under recommended conditions of storage and handling.
|
Other information
|
Polymerisation will occur in the presence of moisture.
|
|
|
11.
|
TOXICOLOGICAL INFORMATION
Inhalation
|
Low volatility. Little risk of inhalation of harmful vapours. Methyl ethyl ketoxime. released during polymerisation of oxime curing silicones is irritating to the respiratory system.
|
Skin
|
Methyl ethyl ketoxime released during polymerisation of oxime curing RTV silicones is a known skin irritant and sensitizer.
|
Eyes
|
Not considered to be an eye irritant. Methyl ethyl ketoxime released during polymerisation of oxime curing RTV silicones is a known eye irritant.
|
Ingestion
|
This product is considered to be of low toxicity. Acute oral (rat) > 2000 mg/kg.
|
|
|
12.
|
ECOLOGICAL INFORMATION
Storage
|
Keep away from water and drains.
|
Ecotoxicity
|
Does not contain any substances listed on the Montreal protocol. Cured Loctite products are typical polymers and do not pose any immediate environmental hazards.
|
Other information
|
Biological and chemical oxygen demands (BOD and COD) of cured Loctite products are insignificant. Precautions required with respect to environmental hazards of articles in which this product is used should be considered.
|
|
|
13.
|
DISPOSAL CONSIDERATIONS
Disposal considerations
|
After use, packaging containing residual product should be disposed of as "chemically contaminated waste" in accordance with local and national legislation and regulations. Incinerate or bury waste" in accordance with local and national legislation and regulations. Dispose of in accordance with local and national regulations. Large quantities of unused products may be disposed as chemical waste after polymerizing. Contribution of this product to waste is very insignificant in comparison to articles in which it is used. Regulations governing disposal of individual articles apply.
|
|
|
14.
|
TRANSPORT INFORMATION
UN-no.
|
None
|
Air (IATA)
|
Not classified
|
Sea (IMO)
|
Not classified
|
Road/Rail (ADR/RID)
|
Not classified
|
|
|
15.
|
REGULATORY INFORMATION
R-phrases
|
None
|
S-phases
|
None
|
Other information
|
Volatile by-products are released during polymerisation. See material safety data sheet for further information.
|
|
|
16.
|
OTHER INFORMATION
The information in this material safety data sheet was obtained from reputable sources and to the best of our knowledge is accurate and current at the mentioned date. Neither Loctite nor its subsidiary companies accept any liability arising out of the use of the information provided here or the use, application or processing of the product(s) described herein. Attention of users is drawn to the possible hazards from improper use of the product(s).
Material safety data sheet revised
|
2001-07-25
|
For more information
|
Loctite Corporation, International Health and Regulatory Affairs, Tallaght Business Park, Whitestown, Dublin 24, Ireland.
Tel: +353-1-4046585
Fax: +353-1-4510806
|
Produced by
|
Caitriona Keane Health & Regulatory Affairs - Europe
|
|
