Bus communication, Trionic T7

Bus communication, Trionic T7

•	Control module, ACC (216)

•	Radio switch C (267c)

•	Control module, airbag/SRS (331)

•	Radio (353)

•	CD changer (355)

•	Control module, PSM (357Dk)

•	Control module, Trionic T7 (430b)

•	Transmission control module, TCM (502b)

•	MIU (540d)

•

SID (541)

•	Control module (ABS) 547

•	Control module STC (565)

•	Control module, Trionic T7 OBDII (589b)

•	Control module, DICE (628)

•	Control module, TWICE (632)

•	Data link connector H16-5/445)

P-bus and I-bus

A bus is the leads over which information is sent digitally and serially. Digital means that the voltage difference between the leads has only two values, roughly 0 V and 5 V. The information is coded so that different combinations of 0 V and 5 V pulses have different meanings.

Serial means that the information is sent in ”packets” one after the other in rapid succession.

The bus is divided into the P-bus (Powertrain Bus) and the I-bus (Instrument Bus). Both buses are connected to the main instrument unit (MIU). The buses are electrically isolated from each other.

Only diesel-engined cars and cars with Trionic T7 have a P-bus. Other petrol-engined variants have the same engine management system and automatic transmission as the earlier 900 model (T5, M2.10.3 and TCM) and these have no bus connections.

As in the 9-5, the Airbag and ABS control modules have no bus connections.

The diagnostics instrument is not directly connected to the bus but communicates via DICE, which is connected to the I-bus, and therefore has access to all the control modules connected to the bus.

The P-bus has a data transfer rate ten times higher than that of the I-bus. This is because the P-bus requires information with the least possible delay.



All the information sent from one control module is accessible for all the other control modules on the bus. The MIU is responsible for making information on one bus available to the other bus.

The control modules send out information on the bus at regular intervals. The time between two transmissions depends on the information being transmitted and varies between 10 milliseconds (0.010 seconds) and one second. Information is also transmitted by the control module whenever the information changes.

The transfer of information between control modules takes place on two leads, bus+ (green lead) and bus- (white lead). The leads are twisted to increase their resistance to electrical interference.

The MIU uses the following information:

Information	Values	From	The value depends on the following sensor input, signal or function
LH direction indicators	ON/OFF	DICE	Control module activation of output to lamps The MIU lights the indicator lamp for LH direction indicators.
RH direction indicators	ON/OFF	DICE	Control module activation of output to lamps The MIU lights the indicator lamp for RH direction indicators.
Rear fog light	ON/OFF	DICE	Control module activation of output to fog light The MIU lights the indicator lamp for the rear fog light.
Driver's door	OPEN/CLOSED	TWICE	Door switch The MIU lights the driver's door symbol.
Passenger's door	OPEN/CLOSED	TWICE	Door switch The MIU lights the passenger's door symbol.
LH rear door	OPEN/CLOSED	TWICE	Door switch The MIU lights the LH rear door symbol
RH rear door	OPEN/CLOSED	TWICE	Door switch The MIU lights the RH rear door symbol.
Boot lid	OPEN/CLOSED	TWICE	Lid switch The MIU lights the boot lid symbol.
Steering wheel location	LHD/RHD	TWICE	Control module programming. The MIU uses the information to indicate door open on the pictogram, driver door/passenger door.
Info Disp Lamp	ON/OFF	SID	The MIU lights the Info Display indicator lamp in the event of a text message.
Rheostat level	0-100 %	SID	Rheostat control module input The MIU uses information on the rheostat setting to control the brightness of the instrument lighting.
Rheostat Night Panel	0-100 %	SID	Rheostat control module input reduced by a fixed value.
Night Panel	ON/OFF	SID	The MIU turns off the lighting of certain instruments and displays.
Display lighting	0-100 %	SID	The MIU uses the information to control the display lighting.
Light intensity in cabin	Lux	SID	The MIU uses the information to control the brightness of indicator lamps.
Check Engine lamp	ON/OFF	T7	Internal diagnosis
SHIFT UP lamp	ON/OFF	T7	Wheel speed front right (lead from ABS)
CRUISE Lamp	ON/OFF	T7	Cruise Control function
TURBO gauge	0-255, no unit	T7	Current air mass per combustion
Fuel Consumed Since Start	0-65535 ml	T7	Fuel injection function
Engine speed	0-7000 rpm	T7	Crankshaft position sensor
Coolant temperature	-40-215°C	T7	Coolant temperature sensor
Selector lever Position	P, R, N, D, 3, 2, 1	TCM	Selector lever position sensor.
CHECK GEARBOX Lamp	ON / OFF	TCM	Internal diagnosis
SPORT	ON / OFF	TCM	The button and oil temperature sensor and not limp-home or WINTER
WINTER	ON / OFF	TCM	The button and oil temperature sensor and not limp-home.

The MIU sends the following information:

Information	Values	Used by	The value depends on the following sensor input, signal or function
Vehicle speed	km/h (mph)	DICE, SID, ACC, Audio, TWICE, STC, T7	Wheel speed, RL (lead from ABS). The MIU controls the speedometer
A/C relay	ON/OFF	DICE	The MIU receives information via a lead to Trionic/Motronic. When the A/C relay is active, the MIU sends this information out on the bus.
Acoustic warning	Acoustic information	SID	Request for acoustic signal when central warning lamp or Info Displ goes on.
Tighten fuel filler cap	ON/OFF	SID	If there is a fault in the tank venting system, the MIU is informed through a lead from Trionic. The main instrument unit sends the information "Tighten fuel filler cap" on the bus. The message is displayed on the SID. OBDII only.
Fuel Consumed Since Start	0-65535 ml	SID	Bus from Trionic T7. The reading is corrected by an adjustment factor in the MIU. The factor can be adjusted with the diagnostics instrument.
Fuel level	litres	SID	Tank sensor, control module adjustment The MIU sends information on the current amount of fuel in the tank.
Odometer reading	km, miles	SID	Display value. Information on distance driven.
Identification number	---	TWICE	The number is generated in the MIU when the immobilization code is programmed in TWICE.
Diagnostics communication	---	DICE/ Diagnostic tool	Control module should be live and the bus leads intact.