Upholstery fabric, seat cushion
|
|
Upholstery fabric, seat cushion
|
|
2.
|
manual front seat:
Remove the handle for height adjustment and the knob for backrest rake adjustment. use a screwdriver.
|
Note
|
|
When removing the knob, note that the backrest recline spindle may be removed with the knob.
|
|
|
3.
|
Remove the seat side panel, 2 caps and 3 screws. Lift the back of the side panel and pull it forwards.
|
Note
|
|
Electrically adjustable seat:
The front bolt has a protector on its tip. Retain this protector as it must be fitted to the bolt to prevent it from chafing against electrical wiring.
|
|
|
4.
|
Electrically adjustable front seat:
Unplug the connector from the switch unit and remove the memory buttons, if any.
|
|
5.
|
Dismantle the seat belt mounting if necessary.
|
|
6.
|
5D:
Remove the plastic covers on each side of the backrest joint.
|
Note
|
|
The plastic covers conceal the holes for access to the screws holding the seat at the rear.
|
|
|
7.
|
Undo the seat cushion at the rear, 2 screws.
|
|
8.
|
Undo the seat cushion at the front, 2 screws.
|
|
9.
|
Detach the straps securing the bottom of the backrest upholstery at the front.
|
|
10.
|
Cut the cable ties. Unplug and mark the connector.
Remove the seat cushion.
|
|
11.
|
Release the upholstery strip at the rear of the seat base.
|
|
12.
|
Release the upholstery strip along the edges of the seat base.
|
|
13.
|
Undo the clamps securing the foam and lift away the seat base from the foam cushion.
|
|
14.
|
Unclip the seat upholstery from the foam cushion.
|
|
15.
|
Remove the seat upholstery.
|
|
1.
|
Fit the seat upholstery over the foam cushion.
|
|
2.
|
Fit the staples using the pliers in fitting kit 84 71 062.
|
|
3.
|
Place the seat base on the foam cushion and fit the clamps.
|
|
4.
|
Replace the strip along the edge of the seat base.
Check the fit and that it is secure.
|
|
5.
|
Position the seat and fit the front screws without tightening them.
|
|
6.
|
Place the screws in the back of the seat cushion, 2 screws.
|
|
7.
|
Tighten the screws in the front of the seat cushion.
|
|
8.
|
5D:
Fit the plastic covers on each side of the backrest joint.
|
|
9.
|
Plug in the connector and attach a new cable tie.
|
|
10.
|
Fasten the straps on the bottom of the backrest upholstery under the seat cushion.
|
|
11.
|
Fit the seat belt mounting where applicable.
Tightening torque 33 Nm
|
|
12.
|
Electrically adjustable seat:
First fit the connector to the switch and any memory buttons on the seat panel.
Fit the seat panel by sliding it into its groove and pressing over the rear edge.
Fasten the seat side panel, 3 screws and 2 caps.
Electrically operated seat:
Fit the protector on the front bolt.
|
|
13.
|
Manual seat:
Fit the handle for the height adjustment and the backrest recliner knob.
|
Note
|
|
If necessary, the backrest upholstery can be detached to make it easier to position the backrest recline spindle. Make sure the backrest upholstery does not get stuck between the side panel and the backrest. The upholster must side panel the spindle.
|
|
