Test readings, control module connections
|
|
Test readings, control module connections
|
The following pages contain directions and readings for testing the control module.
|
•
|
Observe the test criteria. Use common sense when assessing the test results.
|
|
•
|
The test readings presented here are with the ignition ON unless stated otherwise.
|
|
|
-
|
Check first that the control module is receiving power and is grounded.
|
|
|
-
|
Then check all sensor inputs and signals from other systems.
|
|
|
-
|
Finally, check the control module outputs. Remember that the test readings are not a confirmation of whether the actuator is in working order.
|
|
•
|
If a test reading is incorrect, use the wiring diagram to locate the leads, connectors or components that need to be checked further.
|
|
•
|
Specified test readings are for a calibrated Fluke 88/97.
|
|
•
|
Test values show the signal pulse ratio and pulse width respectively. A scan tool with pulse ratio and pulse width measurement respectively must be used.
|
|
Note
|
|
All units on the I and P buses send signals.
|
|
Number of connection pins
|
64
|
|
Pin
|
Component/function
|
In/Out
|
Test criteria
|
Measure across
|
Test reading
|
|
1
|
Not connected
|
Out
|
|
|
|
|
2
|
Not connected
|
|
|
|
|
|
3
|
Not connected
|
|
|
|
|
|
4
|
Button, backrest forward
|
In
|
|
4-59
|
B+
|
|
5
|
Button, backrest backward
|
In
|
|
5-59
|
B+
|
|
6
|
Not connected
|
|
|
|
|
|
7
|
Memory button 3
|
In
|
|
7-59
|
B+
|
|
8
|
Memory button 1
|
In
|
|
8-59
|
B+
|
|
9
|
Memory button 2
|
In
|
|
9-59
|
B+
|
|
10
|
Memory store button
|
In
|
|
10-59
|
B+
|
|
11
|
Button, seat forward
|
In
|
|
11-59
|
B+
|
|
12
|
Not connected
|
|
|
|
|
|
13
|
Not connected
|
|
|
|
|
|
14
|
Button, seat backward
|
Out
|
|
14-59
|
B+
|
|
15
|
Button, tilt forward
|
Out
|
|
15-59
|
B+
|
|
16
|
Button, rear down
|
Out
|
|
16-59
|
B+
|
|
17
|
Button, rear up
|
Out
|
|
17-59
|
B+
|
|
18
|
Button, tilt back
|
Out
|
|
18-59
|
B+
|
|
19
|
Not connected
|
|
|
|
|
|
20
|
Not connected
|
|
|
|
|
|
21
|
Not connected
|
|
|
|
|
|
22
|
Not connected
|
|
|
|
|
|
23
|
Not connected
|
|
|
|
|
|
24
|
Not connected
|
|
|
|
|
|
25
|
Not connected
|
|
|
|
|
|
26
|
Not connected
|
|
|
|
|
|
27
|
Not connected
|
|
|
|
|
|
28
|
Power supply, switch
|
Out
|
|
28-58
|
11.5V-B+
|
|
29
|
Power supply, hall sensor
|
In
|
Motor runs forward or backward
|
29-33
|
7.5-8.5V
|
|
30
|
Ground, hall sensor, tilt
|
In
|
Motor runs up or down
|
30-29
|
7.5-8.5V
|
|
31
|
Ground, hall sensor/backrest forward-backward
|
In
|
Motor runs forward or backward
|
31-29
|
7.5-8.5V
|
|
32
|
Ground, hall sensor/rear up-down
|
In
|
Motor runs up or down
|
32-29
|
7.5-8.5V
|
|
33
|
Ground, hall sensor/seat forward-backward
|
In
|
Motor runs forward or backward
|
33-29
|
7.5-8.5V
|
|
34
|
Not connected
|
|
|
|
|
|
35
|
Not connected
|
|
|
|
|
|
36
|
Not connected
|
|
|
|
|
|
37
|
Not connected
|
|
|
|
|
|
38
|
Not connected
|
|
|
|
|
|
39
|
I-bus
|
In/Out
|
Test lamp
|
39-58
|
Test lamp should flash*
|
|
40
|
Not connected
|
|
|
|
|
|
41
|
Not connected
|
|
|
|
|
|
42
|
Not connected
|
|
|
|
|
|
43
|
Not connected
|
|
|
|
|
|
44
|
Not connected
|
|
|
|
|
|
45
|
Not connected
|
|
|
|
|
|
46
|
Not connected
|
|
|
|
|
|
47
|
Not connected
|
|
|
|
|
|
48
|
Not connected
|
|
|
|
|
|
49
|
Not connected
|
|
|
|
|
|
50
|
Not connected
|
|
|
|
|
|
51
|
Not connected
|
|
|
|
|
|
52
|
Not connected
|
|
|
|
|
|
53
|
Not connected
|
|
|
|
|
|
54
|
Motor, backrest
|
In/Out
|
|
54-55
|
3.8V
|
|
55
|
Motor, backrest
|
In/Out
|
|
55-58
|
3.8V
|
|
56
|
Not connected
|
|
|
|
|
|
57
|
Motor, tilt
|
In/Out
|
|
57-58
|
3.5V
|
|
58
|
Ground
|
In
|
|
58-59
|
B+
|
|
59
|
+30 voltage
|
In
|
|
59-58
|
B+
|
|
60
|
Motor, group 1
|
In/Out
|
|
60-58
|
3.5V
|
|
61
|
Not connected
|
|
|
|
|
|
62
|
Motor, rear height adjustment
|
In/Out
|
|
62-58
|
3.5V
|
|
63
|
Not connected
|
|
|
|
|
|
64
|
Motor, legroom adjustment
|
In/Out
|
|
64-58
|
3.5V
|
*All control modules send a voltage
