Timing belt in car Z19DT
Timing belt in car Z19DT |
To remove |
1. |
Protect the wings with covers.
|
2. |
Remove the battery cover and the negative battery cable.
|
3. |
Raise the car.
|
4. |
Remove the front right wheel.
|
5. |
Remove the right wing liner.
|
6. |
Remove the lower engine cover.
|
7. |
Fit
83 96 145 Centring fixture, subframe - engine
on to the engine subframe and
83 96 368 Supplementary kit to centring fixture
with
32 025 007 Mounting fixture
. Use only the front mounting fixture applied against the A/C compressor bracket. Take the strain off the engine bracket by adjusting the fixture.
|
8. |
Relieve the belt tensioner and lock it with
87 92 335 Lock pin
. Remove the drive belt for the auxiliaries.
|
9. |
Remove the crankshaft pulley.
|
10. |
Remove the idler pulley centre bolt on the lower timing cover. Use, for example, 2 screwdrivers to carefully prise off from two directions.
|
11. |
Lower the car.
|
12. |
Remove the upper engine cover.
|
13. |
Remove the A/C pressure connector and the air filter housing cover with filter.
|
14. |
Remove the air filter housing.
|
15. |
Remove the right-hand engine mounting.
|
16. |
Remove the upper and lower timing covers.
|
17. |
Zero the engine by turning it over so that the camshaft sprocket marking is aligned with the marking on the camshaft cover.
|
18. |
Relieve the belt tensioner and remove the timing belt.
|
19. |
Replace the water pump if it is leaking coolant or if there is play or noise in the bearings.
|
To fit |
1. |
Fit the timing belt.
|
2. |
Raise the car.
|
3. |
Remove the bolt from the oil pump and fit
32 025 009 Crankshaft fixing tool
to the crankshaft sprocket.
|
4. |
Fit the belt tensioner without tightening the bolt.
|
6. |
Remove the adjustment tool and turn the crankshaft 2 turns.
|
7. |
Refit
32 025 009 Crankshaft fixing tool
. Check that the belt is mounted correctly, that the camshaft sprocket marking is aligned with the marking on the camshaft cover and that the tension roller setting arrow is in the centre of the mark.
|
8. |
Remove the tool and fit the bolt to the oil pump.
|
9. |
Fit the lower timing cover.
|
10. |
Fit the upper timing cover.
|
11. |
Fit the right-hand engine mounting.
Tightening torque on engine, 50 Nm (137 lbf ft) Tightening torque to body 40 Nm + 60° (30 lbf ft + 60°). |
12. |
Fit the air filter housing with cover and the connector on the intake hose.
|
13. |
Fit the upper engine cover.
|
14. |
Raise the car.
|
15. |
Fit the idler pulley centre bolt on the lower timing cover.
Tightening torque 25 Nm (18 lbf ft) |
16. |
Fit the crankshaft pulley.
Tightening torque 25 Nm (18 lbf ft) |
17. |
Relieve the belt tensioner and fit the drive belt for the auxiliaries.
|
18. |
Remove the engine fixing tool from the subframe.
|
19. |
Fit the lower engine cover.
|
20. |
Refit the right wing liner.
|
21. |
Fit the front right wheel. See
Wheels
.
|
22. |
Lower the car.
|
23. |
Connect the negative battery cable and fit the battery cover.
|
24. |
Carry out
Procedures after reconnecting the battery
.
|
25. |
Start the engine and turn it off.
|
26. |
Remove the wing cover.
|