Delivery line for power steering, B207 LHD
Delivery line for power steering, B207 LHD |
Important | ||
Scrupulous cleanliness must always be observed during all work with hydraulic components. |
||
Important | ||
Always use wing covers when working in the engine bay. |
||
To remove |
1. |
Lift off the battery cover and disconnect the negative battery cable.
|
2. |
Clamp the return hose using
30 07 739 Hose pinch-off pliers
.
|
3. |
Place a receptacle under the car and detach the delivery line from the steering gear.
|
4. |
Detach the power steering pipe from the power steering pump.
|
5. |
Undo the plastic clips on the delivery line.
|
6. |
Raise the car.
|
7. |
Remove the front right wheel.
|
8. |
Remove the right-hand wheel arch liner.
|
9. |
Remove the front lower cover.
|
10. |
Remove the front bumper shell.
|
11. |
Suspend the radiator assembly from the radiator member with two
83 95 212 Straps
.
|
12. |
Remove the right-hand air shield.
|
13. |
Remove the screw holding the front torque arm to the subframe.
|
14. |
Remove the brake hose clips and unhook the hose from the mounting on the suspension strut.
|
15. |
Remove the bolt from the steering swivel member. Lower the suspension arm and place a
83 95 238 Wedge
between the suspension arm and anti-roll bar.
|
16. |
Tap out the drive shaft from the intermediate shaft using a brass drift and mallet. Move aside the drive shaft.
|
17. |
Place a column jack under the subframe and remove the front bolts.
|
18. |
Open the plastic clip on the subframe and remove the cooling circuit clamps.
|
19. |
Lower the front edge of the subframe.
|
20. |
Remove the power steering pipe.
|
To fit |
1. |
Fit the power steering pipe and cooling coil clamps.
|
2. |
Fit the pipe in the plastic clip outer hole.
|
3. |
Raise the subframe with the column jack and tighten the bolts.
Tightening torque 75 Nm +135° (55 lbf ft +135°) |
4. |
Remove the column jack. Fit the bolt holding the front torque arm to the subframe.
Tightening torque 60 Nm +90° (44 lbf ft +90°) |
5. |
Remove the straps.
|
6. |
Insert the drive shaft into the intermediate shaft. Make sure the lock ring clicks into place.
|
7. |
Fit the brake hose and the clip.
|
8. |
Remove the wedge and attach the ball joint to the steering swivel member with a nut and bolt. The pin must be visible above the steering swivel member before the bolt is fitted. Tighten the nut.
Tightening torque 50 Nm (37 lbf ft) |
9. |
Fit the right-hand air shield.
|
10. |
Fit the wheel arch liner.
|
11. |
Fit the front bumper shell.
|
12. |
Fit the front, lower engine cover.
|
13. |
Fit the wheel.
|
14. |
Lower the car to the floor.
|
15. |
Fit the power steering hose to the steering gear.
Tightening torque 28 Nm (21 lbf ft) |
16. |
Fit the power steering hose to the power steering pump using a new seal, and to the hose clip.
Tightening torque 32 Nm (24 lbf ft) |
17. |
Remove the hose pinch-off pliers.
|
18. |
Connect the negative battery cable and fit the battery cover.
|
19. |
Fill with power steering fluid,
bleed the power steering system
and check for leaks.
|
20. |
Perform the measures necessary for after disconnecting the battery.
|