Component
|
Nm
|
Starter motor on gearbox
|
40
|
Starter motor on cylinder block
|
25
|
Belt pulley on crankshaft
|
60
Use new retaining bolts.
|
Exhaust manifold on cylinder head
|
13
|
Battery holder on body
|
15
|
Cover on oil filter housing
|
15
|
Throttle valve connection on intake manifold
|
8
|
Intake pipe pressure sensor in intake manifold
|
8
|
Dynamic oil level control on oil sump
|
8
Recut the threads before reuse and apply locking compound (red) when fitting the bolts. Mounting time including checking torque must not exceed 10 min.
|
Intake manifold on cylinder head
|
20
|
Accelerator pedal on bulkhead
|
12
|
Generator on generator stay
|
20
|
Gearbox on engine block
|
60
|
Generator attaching plate on engine block
|
35
|
Engine pad attachment (left) on gearbox
|
35
|
Engine pad attachment (right) on engine block
|
65 + 45° + 15°
|
Crankshaft impulse sensor holder on oil pump/engine block
|
10
|
Rear engine pad holder on gearbox
|
80
|
Engine pad holder on engine pad attachment (left)
|
55
|
Engine pad holder on engine pad attachment (right)
|
55
|
Dipstick guide tube holder on exhaust return adapter
|
8
|
Rear tooth belt cover on cylinder head and oil pump
|
6
|
Heat shield on exhaust manifold
|
8
|
Crankshaft impulse sensor on holder/oil pump
|
8
|
Increment disc (vibration damper) on crankshaft
|
95 + 30° + 15°
|
Bulkhead finishing plate insulation on body
|
9
|
Cable duct on engine block
|
35
|
Refrigerant pipe on accumulator
|
20
|
Refrigerant pipe on refrigerant pipe
|
20
|
Multi-belt tensioner on generator attachment
|
35
|
Knock sensor on cylinder head
|
20
|
Fuel pipe(s) on fuel rail
|
30
|
Fuel rail on intake manifold
|
8
|
Coolant pipe on intake manifold and camshaft cover
|
8
|
Coolant pump on engine block
|
8
|
Coolant pipe on engine block/gearbox
|
60
|
Crankshaft bearing cap on engine block
|
50 + 45° + 15°
|
Lambda sensor fuel regulator on exhaust manifold
|
40
|
Lambda sensor catalytic converter control on front exhaust pipe
|
40
|
Generator bracket on intake manifold, coolant flange and generator
|
20
|
Air filter housing on body
|
2,5
|
Fan cowl on radiator
|
5
|
Rear engine pad on holder
|
55
|
Rear engine pad on front axle member
|
55
|
Engine pad (left) on body (longitudinal member)
|
20
|
Engine pad (right) on body (longitudinal member)
|
35
|
Engine pad (front) on gearbox
|
60
|
Engine pad (front) on front axle member
|
55
|
Engine control module on intake manifold
|
8
|
Engine transport lug on cylinder head
|
25
|
Camshaft bearing cap on cylinder head
|
8
|
Camshaft sprocket on camshaft
|
50 + 60° + 15°
|
Camshaft sensor on cylinder head
|
8
|
Upper generator retaining bolt on generator bracket
|
20
|
Oil drain screw on oil pan (inner torx screw)
|
14
|
Oil drain screw on oil pan (hex screw)
|
45
|
Oil pressure switch on oil pump
|
30
|
Oil filter housing on engine block
|
45
|
Oil pipes (automatic transmission) on radiator
|
25
|
Oil pump on engine block
|
10
|
Oil pump cover on oil pump
|
6
|
Oil intake pipe on oil pump
|
8
|
Oil intake pipe on engine block
|
8
|
Oil pan on gearcase
|
40
|
Oil pan on engine block and oil pump
|
10
|
Big-end bearing cap on connecting rod
|
25 + 30°
|
Wheel on wheel hub
|
110
|
Pitman arm on suspension strut
|
65
|
Air intake hose clamps
|
3,5
|
Flywheel on crankshaft
|
35 + 30° + 15°
|
Coolant temperature sensor on thermostat housing
|
20
|
Intake manifold support on intake manifold
|
20
|
Intake manifold support on engine block
|
35
|
Thermostat housing on cylinder head
|
20
|
Lower generator retaining bolt on generator bracket.
|
35
|
Lower radiator bracket on front axle member
|
15
|
Condenser on radiator
|
5
|
Relief valve seal screw on oil pump
|
50
|
Front axle member on body (all bolts)
|
90 + 45° + 15°
|
Front exhaust pipe on exhaust manifold
|
20
|
Upper part of tooth belt cover on rear tooth belt cover
|
4
|
Lower part of tooth belt cover on rear tooth belt cover
|
4
|
Tooth belt tensioning pulley on oil pump
|
20
|
Tooth belt idler pulley (exhaust side) on engine pad bracket
|
25
|
Tooth belt idler pulley (inlet side) on cylinder head
|
25
|
Spark plug on cylinder head
|
25
|
Ignition discharge module on camshaft cover
|
8
|
Extra fan cowl on radiator/condenser
|
5
|
Intermediate spindle on steering intermediate spindle
|
22
Fit the new retaining bolts with locking compound (red).
|
Cylinder head on cylinder block
|
25 + 90° + 90° + 90° + 45°
|
Camshaft cover on cylinder head
|
8
|