SAAB WIS ONLINE

Camshaft Replacement - Left Side

Camshaft Replacement - Left Side



Special Tools

EN-46111 Crankshaft Rotation Socket

EN-48313 Timing Chain Retention Tool


For equivalent regional tools, refer to Special Tools .

Removal Procedure


1. Remove the intake manifold. Refer to Intake Manifold Replacement .

2. Remove the fuel pump from the cylinder head. Refer to Fuel Pump Replacement .

3. Remove the left bank camshaft cover. Refer to Camshaft Cover Replacement - Left Side (LAU) ; Camshaft Cover Replacement - Left Side (LF1 or LFW) .

4. Remove the camshaft sensors. Refer to Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust and Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake .

5. Remove the camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake .

6. Remove the camshaft position actuator. Refer to Camshaft Position Actuator Replacement - Bank 2 (LF1 or LFW) .

7. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement .

8. Rotate the crankshaft with the socket EN-46111 until the camshaft is in neutral position (low voltage). The camshaft flats must be parallel with camshaft cover's rail (1).


9. Refer to Torque Reaction Against Timing Drive Chain Caution .

Note
Use an open-end wrench at the camshaft hex to prevent camshaft/engine rotation.

DO NOT remove the camshaft position actuator bolt at this time.


Loosen the camshaft position actuator bolt.


10.
Note

Ensure that the tips of the EN-46313 tool are fully engaged into the timing chain.


Install the EN-48313 tool in order to retain the timing chain.

Firmly tighten the EN-48313 tool nuts .

11.
Note

Ensure that the camshaft timing chain and the camshaft position actuators are marked for proper assembly.


Mark the timing chain and the respective locations on the camshaft position actuators (1-4).


12. Remove the camshaft position actuator bolt.

13. Remove the camshafts. Refer to Camshaft Removal - Left Side .


Installation Procedure


1.
Note
Ensure that the marks on the camshaft position actuator and the timing chain (1-4) are aligned.

DO NOT tighten the camshaft position actuator bolt at this time.


Locate the camshafts to the cylinder head and assemble the camshaft actuators to the camshafts.


2. Install the camshafts and the camshaft bearing caps. Refer to Camshaft Installation - Left Side .

3. Remove the EN-46108 tool .

4. Refer to Torque Reaction Against Timing Drive Chain Caution .

Note

Use an open-end wrench at the camshaft hex to prevent camshaft/engine rotation.


Install and tighten the camshaft position actuators. Refer to Camshaft Position Actuator Installation - Left Side Intake and Camshaft Position Actuator Installation - Left Side Exhaust .


5. Install the intake camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake .

6. Install the camshaft sensors. Refer to Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust and Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake .

7. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement .

8. Install the camshaft cover. Refer to Camshaft Cover Replacement - Left Side (LAU) Camshaft Cover Replacement - Left Side (LF1 or LFW) .

9. Install the fuel pump in the cylinder head. Refer to Fuel Pump Replacement .

10. Install the intake manifold. Refer to Intake Manifold Replacement .