SAAB WIS ONLINE

Camshaft Replacement - Right Side

Camshaft Replacement - Right Side



Special Tools

• EN-46111 Crankshaft Rotation Socket

• EN-46313 Timing Chain Retention Tool


For equivalent regional tools, refer to Special Tools .

Removal Procedure


1. Remove the intake manifold. Refer to Intake Manifold Replacement .

2. Remove the camshaft cover. Refer to Camshaft Cover Replacement - Right Side (LAU) Camshaft Cover Replacement - Right Side (LF1 or LFW) .

3. Remove the camshaft sensors. Refer to Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust and Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake .

4. Remove the intake camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake .

5. If equipped with LF1 engine remove the camshaft position actuator . Refer to Camshaft Position Actuator Replacement - Bank 1 (LF1 or LFW) .

6. If equipped with LAU engine remove the camshaft position actuator. Refer to Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake (LAU) .

7. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement .

8. Rotate the crankshaft with the EN-46111 socket until the camshafts are in a neutral (low tension) position.

The camshaft flats will be parallel with the camshaft cover rail (1).


9. Refer to Torque Reaction Against Timing Drive Chain Caution .

Note
• Use an open-end wrench at the camshaft hex to prevent camshaft/engine rotation.

• DO NOT remove the camshaft position actuator bolt at this time.


Loosen the camshaft position actuator bolt.


10.
Note

Ensure that the tips of the EN-46313 tool are fully engaged into the timing chain.


Install the EN-46313 tool in order to retain the timing chain.

Firmly tighten the EN-46313 tool nuts .

11.
Note

Ensure that the camshaft timing chain and the camshaft position actuators are marked for proper assembly.


Mark the timing chain and the respective locations on camshaft position actuators (15-18).


12. Remove the camshaft position actuator bolt.

13. Remove the camshaft bearing caps and the camshaft. Refer to Camshaft Removal - Right Side .


Installation Procedure


1.
Note
• Ensure that the marks on the camshaft position actuators and the timing chain (15-18) are aligned.

• DO NOT tighten the camshaft position actuator bolt at this time.


Locate the camshafts to the cylinder head and assemble the camshaft actuators to the camshafts.


2. Install the camshafts and the camshaft bearing caps. Refer to Camshaft Installation - Right Side .

3. Remove the EN-46313 tool .

4. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement .

5. Refer to Torque Reaction Against Timing Drive Chain Caution .

Note

Use an open-end wrench at the camshaft hex to prevent camshaft/engine rotation.


If equipped with LF1 engine Install the camshaft position actuator . Refer to Camshaft Position Actuator Replacement - Bank 1 (LF1 or LFW) .


6. If equipped with LAU engine Install the camshaft position actuator. Refer to Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake (LAU) .

7. Install the intake camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake .

8. Install the camshaft sensors. Refer to Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust and Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake .

9. Install the camshaft cover. Refer to Camshaft Cover Replacement - Right Side (LAU) Camshaft Cover Replacement - Right Side (LF1 or LFW) .

10. Install the intake manifold. Refer to Intake Manifold Replacement .