SAAB WIS ONLINE

Plastic Collar Quick Connect Fitting Service

Plastic Collar Quick Connect Fitting Service

Removal Procedure


1. Refer to Gasoline/Gasoline Vapors Warning .

Note

There are several types of Plastic Collar Fuel and Evaporative Emission Quick Connect Fittings used on this vehicle.

• Bartholomew (1)

• Q Release (2)

• Squeeze to Release (3)

• Sliding Retainer (4)

• Global Connect (5)

• TI Loc (6)

• Safe Lock (7)

The following instructions apply to all of these types of Plastic Collar Quick Connect Fittings except where indicated.


Relieve the fuel system pressure before servicing any fuel system connection. Refer to the Fuel Pressure Relief .


2.
Warning

Always add some drops of clean engine oil onto the male connector before fitting the fuel pipe connectors. This ensures correct reconnection and prevents any fuel leakage. Always replace O-rings.


Using compressed air, blow any dirt out of the quick-connect fitting.


3. This step ONLY applies to Bartholomew type connections. Press together the quick-coupling's plastic lock tabs in order to release the coupling.


4. This stage ONLY applies for connections of the Q-release type. Release the coupling by moving the lock tab over to the other side of the groove in the coupling.


5. This step applies to Squeeze to Release style connectors ONLY. Squeeze where indicated by arrows on both sides of the plastic ring surrounding the quick-connect fitting.


6. This step applies to Squeeze to Release style connectors ONLY. Push in the male side slightly in order to slide the retainer away from the retainers, squeeze where indicated by arrows on both sides of the plastic ring surrounding the quick-connect fitting.


7. This step applies to Sliding Retainer style connectors ONLY. Release the fitting by pressing on one side of the release tab by pressing it in slightly. If the tab doesn't move try pressing the tab in from the opposite side. The tab will only move in one direction.


8. This step applies to the Global Connector style only. Push the connector toward the tube in order to release the pressure. Press and hold down the release mechanism, and pull the connector straight out.


9. This step only applies for the TI Loc type. Push the connector toward the tube in order to release the pressure. Release the redundant latch (1) with two fingers or a flat bladed tool. Then press and hold down the bottom release mechanism (2) and pull the connector straight out.


10. This step only applies for the safety catch type. Push the connector toward the tube in order to release the pressure. Release the second latch (1) with two fingers. Then press and hold down the bottom release mechanism (2) and pull the connector straight out.

Refer to Relieving Fuel Pressure Warning .


11. Using a clean shop towel, wipe off the male pipe end.

12. Inspect both ends of the fitting for dirt and burrs.

13. Clean or replace the components as required.


Installation Procedure


1.
Warning

Always apply a few drops of clean engine oil to the male pipe ends before connecting the fuel pipe fittings in order to reduce the risk of fire and personal injury. This ensures correct reconnection and prevents any fuel leakage. Always replace O-rings.


Apply a few drops of clean engine oil to the male pipe end.


2. Push both sides of the quick-connect fitting together in order to cause the retaining feature to snap into place.


3. Pull on both sides of the quick-connect fitting to make sure the connection is secure.


4. Insert the tube in the connector until the retainer snaps in place.


5. Push down on the redundant latch (1) until it is fully engaged and snapped into position.

6. Insert the tube in the connector until the retainer snaps in place.


7. Push down on the second latch (1) in order to secure the connection.

8. Inspect for leaks using the following procedure:

8.1. Turn the ignition ON, with the engine OFF for 2 seconds.

8.2. Turn the ignition OFF, for 10 seconds.

8.3. Turn the ignition ON, with the engine OFF for 2 seconds.

8.4. Turn the ignition OFF.

8.5. Inspect for leaks.