Gear selector position sensor
|
|
Gear selector position sensor
|
|
1.
|
Remove the battery cover, battery and battery tray.
|
|
2.
|
Clean round the place where the fluid filler pipe enters the transmission.
|
|
3.
|
Remove the fluid filler pipe.
|
|
4.
|
Move the selector lever to position 1 and undo the lever's retaining nut.
|
|
6.
|
Remove the gear selector position sensor's retaining bolts.
|
|
7.
|
Remove the gear selector position sensor's nut.
|
|
8.
|
Unplug the connector and lift the sensor off the shaft.
|
|
1.
|
Plug in the connector and mount the sensor on the shaft.
|
|
2.
|
Screw on the gear selector position sensor's nut.
Tightening torque: 8 Nm (6 lbf ft)
|
|
4.
|
Clean and lubricate the fluid filler pipe's O-ring with petroleum jelly (Vaseline).
|
|
5.
|
Turn the sensor until that the line marked on it is visible in the centre of the tool's notch and tighten the bolts.
Tightening torque: 25 Nm (18.5 lbf ft)
Refit the fluid filler pipe.
Tightening torque: 22 Nm (16 lbf ft)
|
|
6.
|
Remove the tool and refit the lever. Before tightening the nut, move the selector lever to position P (to relieve the cable of tension).
Tightening torque: 25 Nm (18.5 lbf ft)
|
|
7.
|
Fit the battery tray, the battery and the battery cover. Connect and secure the cables.
|
|
8.
|
Check that the engine starts when the selector lever is in positions P and N. The engine should not start if the selector lever is in position R, D, 3, 2 or 1. The reversing light should light up only in position R.
|
|
9.
|
Set the right time on the clock.
|
Important
|
|
On cars with a shift-lock function, incorrect adjustment of the gear selector position sensor could result in disablement of this function (SHIFT-LOCK).
|
|
|
|
|
1.
|
Remove the battery cover, battery and battery tray.
|
|
2.
|
Move the selector lever to position 1 (to relieve the cable of tension) and undo the lever's nut.
|
|
|
•
|
If it is not, the sensor must be adjusted. Continue with step 4.
|
|
|
•
|
If it is, continue with step 9.
|
|
4.
|
Clean round the fluid filler pipe where it enters the transmission.
|
|
5.
|
Remove the fluid filler pipe's nut and remove the pipe.
|
|
6.
|
Undo the gear selector position sensor's bolts.
|
|
7.
|
Turn the sensor until that the line marked on it is visible in the centre of the tool's notch and tighten the bolts.
Tightening torque: 25 Nm (18.5 lbf ft)
|
|
8.
|
Clean and lubricate the fluid filler pipe's O-ring with petroleum jelly (Vaseline) and fit the fluid filler pipe.
Tightening torque: 22 Nm (16 lbf ft)
|
|
9.
|
Remove the tool and fit the selector lever cable's lever.
Before tightening the nut, move the selector lever to position P (to relieve the cable of tension).
Tightening torque: 25 Nm (18.5 lbf ft)
|
|
10.
|
Refit the battery tray, battery and battery cover.
|
|
11.
|
Check that the engine starts when the selector lever is in positions P and N. The engine should not start if the selector lever is in position R, D, 3, 2 or 1. The reversing light should light up only in position R.
|
|
12.
|
Set the right time on the clock.
|
Important
|
|
On cars with a shift-lock function, incorrect adjustment of the gear selector position sensor could result in disablement of this function (SHIFT-LOCK).
|
|
|
|
