SAAB WIS ONLINE

Body dimensions

Body dimensions

Measurements, body above

These measurements are suitable for determining if the car should be mounted in an alignment bench.








Pos Dimension, mm Measuring points
1

4508

Total length. Front bumper member - Rear bumper bracket

2

885±1

Hole for rubber buffer (*) - Hole for plastic clip, windscreen cover (*)

3

1010±1

Hole for rubber buffer (*) - Front hole in windscreen wiper mechanism bracket (*)

4

1593±1

Hole for rubber buffer (*) - Hole for plastic clip, windscreen cover, diagonal (*)

5

1240±1

Hole for rubber buffer RH side (*) - Hole for rubber buffer LH side (*)

6

642±1

Outer rear hole, MacPherson strut (*) - Front hole in holder. windscreen wiper mechanism (*)

7

1232±1

Outer rear hole, MacPherson strut, RH side (*) - Outer rear hole, MacPherson strut, LH side (*)

8

1429±1

Lower section A pillar - Upper section A pillar, diagonally

9

1499±1

Distance between weatherstrip ribs on top of door sill



(*) = dimension is measured from the centre of the hole.

Measurements, body rear, side




Pos Dimension, mm Measuring points
10

1102±1

Upper hole, front hinge (*) - Lower hole, rear hinge (*)

11

1146±1

Lower hole, front hinge (*) - Upper hole, rear hinge (*)

12

1006±1

Lower hole, rear hinge (*) - Upper hole, striking plate, rear door (*)

13

941±1

Upper hole, rear hinge (*) - Upper hole, striking plate, rear door (*)

14

1177±1

Distance between rear side panels, lower rear corner

15

1054±1

Distance between lower holes for bumper (*)

16

1237±1

Rear side panel, lower rear corner - Lower hole for bumper, diagonal (*)



(*) = dimension is measured from the centre of the hole.

Measurements, body B pillar




Pos Dimension, mm Measuring points
17

1611±1

Elongated hole under seat-belt bolt (*) - Large hole at front of B pillar under elongated hole for B pillar trim retaining clip (*)

18

1504±1

Distance between holes RH - LH side (*)



(*) = dimension is measured from the centre of the hole.

Measurements, body below


Illustration A shows the correct measuring direction for measurements 19, 20, 26 and 27


Illustration B shows the incorrect measuring direction for measurements 19, 20, 26 and 27




Pos Dimension, mm Measuring points
19

1528±1

Hole in wheel housing, behind collision box (*) - Hole in floor reinforcement, inner hole, diagonal (*). Fig. A shows correct measuring direction.

20

1171±1

Hole in wheel housing, behind collision box (*) - Hole in floor reinforcement, inner hole (*). Fig. A shows correct measuring direction.

21

964±1

Hole in wheel housing, behind collision box RH side (*) - Hole in wheel housing, behind collision box LH side (*).

22

1000±1

Hole in floor reinforcement, inner hole RH side (*) - Hole in floor reinforcement, inner hole LH side (*).

23

1350±1

Distance between ribs underneath door sill (refers to max. distance between pressings).

24

1258±1

Hole in frame member ahead of rear axle mounting RH side (*) - Hole in frame member ahead of rear axle mounting LH side (*)

25

1053±1

Hole in frame member ahead of collision box, rear bumper abutment RH side (*) - Hole in frame member ahead of collision box, rear bumper abutment LH side (*)

26

1756±1

Hole in frame member ahead of rear axle mounting (*) - Hole in frame member ahead of collision box, rear bumper abutment diagonal (*). Fig. A shows correct measurement direction.

27

1327±1

Hole in frame member ahead of rear axle mounting (*) - Hole in frame member ahead of collision box, rear bumper abutment (*). Fig. A shows correct measuring direction.



(*) = dimension is measured from the centre of the hole.

Measurements, body rear 5D


Pos Dimension, mm Measuring points
28

1272±1

Square hole for clip to scuff plate (*) - Inner radius, top luggage compartment opening where dimension is greatest.

29

1320±1

Upper hole for bumper (*) - Outer hole for tailgate hinge (*)



(*) = dimension is measured from the centre of the hole.