SAAB WIS ONLINE

To assemble the engine

To assemble the engine

Wash all sealing surfaces with benzine, making sure that they are perfectly clean.



1. Fit all main bearings in position and oil them.

2. Fit the slotted ring. Lock the bolts with part No. (10) 74 96 268. Place the crankshaft in position.

Important

The slotted ring must be handled with great care. Make sure that the main bearing member's adjuster sleeves are unscrewed if they are not fitted tightly in place.


3. Oil all main bearing caps and fit them in their places, making sure that they are the right way round. Fit the main bearing member and tighten the main bearing cap bolts.


Tightening torque:

50 Nm (37 lbf ft) + 60°± 15°

4. Screw the adjuster sleeves down flush. Coat the main bearing member bolts with part No. (10) 74 96 268 and tighten them.

Tightening torque: 20 Nm (15 lbf ft)

5. Spray part No. (10) 81 52 381 into the mating joints at the rear main bearing. Do not stop until the compound is forced out at the sides.

6. Turn the engine and angle it so that cylinders 1-3-5 are vertical. Oil these pistons and rings, adjust the position of the ring gaps and fit the pistons in their cylinders.


The arrow on the crown of the piston must be facing the timing end of the engine. Use Piston fitting tool part no. 83 95 113 and carefully tap down the pistons into the cylinder bores. Repeat for cylinders 2-4-6.

7. Oil and fit all big-end bearing caps in their respective places, making sure they are fitted the right way round. Blow the contact surfaces clean with compressed air. If they are damaged the connecting rod must be changed.


Tightening torque:

35 Nm (26 lbf ft) + 45°± 15°

8. Fit a new rear crankshaft seal using Fitting set for rear crankshaft seal part no. 83 94 967 and part no. 83 94 975. Fit the drive plate. Coat the bolts with part no. (10) 74 96 292.


Tightening torque: 65 Nm (48 lbf ft) + 30°

9. Fit the oil pump with a new gasket. Coat the gasket with part No. (10) 93 21 795.


10. Fit a new front crankshaft seal. Use Fitting set for front crankshaft seal part no. 83 94 942.

11. Fit Counterstay 83 95 063. Coat the back of the camshaft belt sprocket with part no. (10) 93 21 795 and tighten the sprocket.

Tightening torque:

250 Nm (184.5 lbf ft) + 45°

12. Connect the oil pressure sensor.

13. Turn the engine. Apply part No. (10) 81 52 381 to the mating joints.


14. Fit the oil antislosh baffle. Lock the bolts with part No. (10) 74 96 268.


Tightening torque: 8 Nm (6 lbf ft)

15. Fit the oil suction pipe complete with O-ring. Lock the bolts with part No. (10) 74 96 268.

Tightening torque: 8 Nm (6 lbf ft)

16. Fit the oil sump with a new gasket. Secure the bolts with part No. (10) 74 96 268. Check that the drain plug is tightened firmly.

Tightening torque:

Oil sump: 15 Nm (11 lbf ft)

Drain plug 25 Nm (18.5 lbf ft)

17. Turn over the engine. Clean the heat exchanger cover with benzine. Apply 87 81 841 Silicone flange sealant to the sealing surfaces. Fit the heat exchanger with new O-rings. Tighten the cover.


Tightening torque: 20 Nm (15 lbf ft)

18. Connect the oil pipes to the heat exchanger using new seals. Tighten the connections.

Tightening torque: 30 Nm (22 lbf ft).

19. Fit new cylinder head gaskets, minding the oil passages.


For cylinders 1-3-5, the marking OBEN/TOP must face the gearbox end and for cylinders 2-4-6, the marking must face the timing end of the engine.

20. Rotate the crankshaft to 60° BTDC. Fit the cylinder heads with new bolts. Tighten the bolts in the order shown in the illustration.


Tightening torque:

25 Nm (18.5 lbf ft) + 90°

21. Remove the protective sleeves and fit the valve tappets.


22. Place the camshafts in position and fit the stuffing boxes and bearing caps. Start where the cams point downwards and load the tappets. Coat the cylinder head contact surfaces of the front bearing caps sparingly with part No. (10) 74 96 268, see illustration.

Cylinders 1-3-5 (rear)

The locating pin on the camshafts should point towards the inside bolts for the camshaft bearing caps.

Cylinders 2-4-6 (front)

The locating pin for the intake camshaft should be in line (downwards) with the inside bolts for the camshaft bearing caps.

The guide pin for the exhaust camshaft should point straight up from the plane of the cylinder head.

Tightening torque: 8 Nm (6 lbf ft)

Important

Tighten the bolts in stages - 1/2 to 1 turn at a time. The markings on the camshaft bearing caps and the cylinder head must match.

The caps marked L1-L8 are for the cylinder head with cylinders 1-3-5 and the caps marked R1-R8 are for the cylinder head with cylinder 2-4-6. The camshaft bearing seats in each cylinder head are numbered 1-8.


23. Fit the inner (rear) timing cover.


24. Fit the coolant pump with a new O-ring. Coat the O-ring and sealing surface on the cylinder block with non-acidic vaseline.

Tightening torque: 25 Nm (18.5 lbf ft).

25. Fit the new adjuster roller.

Tightening torque: 40 Nm (30 lbf ft)

26. Fit the bracket with tensioning roller and the upper adjuster roller.

27. Lubricate and fit new camshaft seals with Assembly tool for camshaft seal part no. 83 94 959. Fit the camshaft sprockets.


The number in the sprocket hub should match the number on the camshaft.

Tightening torque: 50 Nm (37 lbf ft) + 60°

Warning

The jaws of the open-ended spanner used as a counterstay when fitting the camshaft sprockets must not be too long. There is otherwise a risk of damaging the metal so that the tappets become locked.


28. Carefully turn the camshafts so that the markings on the camshaft sprockets are aligned with the grooves on the inner (rear) timing cover. Use KM-800-20. Lock the camshafts with Installation tool for camshaft sprockets and camshaft drive belt KM-800-1 (cylinders 1-3-5) and KM-800-2 (cylinders 2-4-6).

29. Turn the crankshaft in the direction of rotation of the engine until just before TDC. Fit KM-800-10 on the crankshaft and turn the crankshaft to TDC. Press the movable arm against the flat part of the coolant pump flange and attach it.


30. Put on the camshaft belt according to the markings on the belt and the marked direction of rotation. Use Adjustment tools for cam sprocket and timing belt KM-800-30 to keep the belt in place. Fit the lower tensioning pulley loosely. Make sure the washer is in place. Adjust the tensioning pulley by hand so that the belt does not jump. Adjust anti-clockwise. Make sure the markings on the timing belt and the corresponding markings on the cam sprocket and crankshaft are aligned. Remove the tool KM-800-30.

Fit locking tool KM-800-10, position a piece of camshaft belt and fit Belt tension meter part no. 83 93 985 to measure the belt tension.

Tighten the centre bolts of the adjuster rollers lightly. Adjust the lower adjuster roller anticlockwise until a tension of 275-300 Nm is obtained. Use tool 83 94 983. Tighten the adjuster roller's bolt. Use tool 83 94 983 as a counterstay. Check the belt tension again and adjust as necessary.

Tightening torque: 40 Nm (30 lbf ft)

Remove the belt-tension meter and piece of the toothed belt.

Important

Adjustment of belt tension is only a preparatory measure and must not be used as a check when the belt is finally adjusted.


31. Ensure the adjusting nut on the upper adjusting roller rotates freely and is not tight. Adjust the tensioning pulley with a 5 mm Allen key until the two lines on the tensioning pulley correspond with each other. Tighten.


Tightening torque: 20 Nm (15 lbf ft)

Remove the locking tool for camshaft sprockets 1 and 2. Fit tool KM-800-20. Then, adjust the upper adjusting roller anticlockwise with tool 83 94 983 until the markings on the camshaft sprocket are aligned with the corresponding markings on KM-800-20. Tighten. Use tool 83 94 983 as a counterstay.

Tightening torque: 40 Nm (30 lbf ft)

Remove KM-800-20 and the other locking tools.

32. Turn the crankshaft two revolutions until just before the zero mark and fit locking tool KM-800-10 on it. Carefully turn the crankshaft in the engine's direction of rotation until the arm abuts against the coolant pump flange and tighten it. Fit tool KM-800-20 and check that the markings on the camshaft sprockets are opposite the markings on the tool and that the edge of the belt coincides with the edge of the sprockets.

Important

Check that marking A is about 2 mm above marking B. If this distance is smaller, adjustment must be carried out afresh.


33. Fit the timing cover.


34. Fit the coolant pump pulley and crankshaft pulley.

Tightening torque:

Belt pulley/coolant pump: 8 Nm (6 lbf ft)

Belt pulley/crankshaft: 20 Nm (15 lbf ft)

35. Fit new gaskets on the camshaft covers and wipe clean. Lubricate with a soap solution and place part No. (10) 81 52 381 in the corners at the camshaft bearing caps. Fit the camshaft covers.


Tightening torque: 8 Nm (6 lbf ft)

36. Fit the spark plugs using spark plug socket 83 95 485.

Tightening torque: 25 Nm (18.5 lbf ft).

37. Fit the ignition discharge modules. Connect the cables to the ignition discharge modules and fit the engine wiring harness.

38. Fit the crankcase breather housing.


39. Fit the coolant bridge with new copper gaskets. Coat the bolts with part No. (10) 74 96 284.

Tightening torque: 30 Nm (22 lbf ft).

40. Fit the thermostat with a new O-ring. Moisten the O-ring with coolant.

Tightening torque: 20 Nm (15 lbf ft)

41. Refit the coolant pipe with new O-rings. This will be easier if the O-rings are moistened with coolant.

42. Fit the lower intake manifold with new gaskets.


Tightening torque: 20 Nm (15 lbf ft)

43. Fit the middle intake manifold. Connect the cables to the injectors.

Tightening torque: 20 Nm (15 lbf ft)

44. Fit the upper intake manifold with a new gasket.

Tightening torque: 20 Nm (15 lbf ft)

45. Fit the front exhaust manifold with a new gasket. Clean the sealing surfaces before fitting.


Tightening torque: 20 Nm (15 lbf ft)

Note

Coat the studs and gaskets thinly with Molycote 1000, part No. 30 20 971, or the like to prevent them from baking on.


46. Fit the rear exhaust manifold with a new gasket. Fit the heat shield over the rear exhaust manifold.


47. Fit the oil filter and connect the oil filter adapter's oil pipes.


Tightening torque:

Oil filter 10 Nm (7.5 lbf ft)

Oil pipe 25 Nm (18.5 lbf ft)

48. Fit the crankshaft position sensor with a new O-ring.

Tightening torque: 8 Nm (6 lbf ft)

49. Connect the turbo's water and oil pipes.

Tightening torque:

Oil return pipe, M6 bolt: 14 Nm (10 lbf ft)

Oil pipe, turbo: 20 Nm (15 lbf ft)

Oil pipe, oil filter adapter: 20 Nm (15 lbf ft)

Water pipe: 25 Nm (18.5 lbf ft)

Cylinder head retaining bolt 14 Nm (10 lbf ft)

Important

It is extremely important for oil to be present in the turbocharger when the engine starts.

Fill the turbo's oil inlet and pipe with oil. Spin the turbine wheel (impeller) several times to lubricate the bearings with oil.


50. Fit the turbo's bracket.

Tightening torque: 24 Nm (18 lbf ft)

51. Fit the dipstick.

52. Connect the cable to the oil pressure sensor.


53. Connect the temperature sensor to the coolant bridge.

54. Connect the vacuum hose and water hose to the throttle. Also plug in the throttle's connector.

55. Fit and connect the generator. Connect the cable for the oil pressure sensor to the generator.


56. Fit the belt tensioner.

Tightening torque: 40 Nm (30 lbf ft)

57. Fit a lifting sling and lift the power unit away from the stand. Remove the holder.

58. Position the gearbox and tighten the bolts. Fit the front exhaust pipe with heated oxygen sensor, power steering pump and power unit to the subframe.


Tightening torque:

Gearbox: 70 Nm (52 lbf ft)

59. Remove the torque converter's fixing tool.

60. Bolt the drive plate and torque converter together by gradually rotating the crankshaft so that all the bolts can be tightened.

Turning torque: 60 Nm (44 lbf ft).

61. Fit the plastic plug under the starter motor.

62. Fit the starter motor and connect the cables.

63. Fit the support bearing bracket with pipe and inboard drive-shaft universal joint.

64. Fit the bracket for the engine wiring harness.


65. Fill up with oil.


The power unit is now ready to be fitted in the car.