Coolant pump, 4-cyl.
Coolant pump, 4-cyl. |
|
To remove |
1. |
Open the cap on the expansion tank and release the pressure.
|
2. |
Raise the car.
|
3. |
Remove the lower front cover.
|
4. |
Drain off the coolant.
|
5. |
Lower the car to the floor.
|
6. |
Unplug the mass air flow sensor connector.
|
7. |
Remove the air hose and mass air flow sensor.
|
8. |
Off-load the multigroove V-belt using the pull bar, part no. 83 95 254.
|
9. |
Remove the belt from the power steering pump and water pump.
|
10. |
Remove the crankcase breather pipe, fastened to the turbo intake pipe, and the camshaft cover.
|
11. |
Unplug the boost pressure control valve connector.
|
12. |
Remove the engine lifting eyelet.
|
13. |
Loosen the hoses to the turbo's wastegate valve.
|
14. |
Remove the bypass pipe with valve.
|
15. |
Remove the exhaust manifold heat shield. The heat shield is attached with a nut and two clips on the underside.
|
16. |
Undo the quick-release coupling on the vent hose, using tool 83 95 261.
|
17. |
Remove the turbo intake pipe.
|
18. |
Remove the intake pipe.
|
19. |
Plug the turbo inlet using a plastic plug or the like.
|
20. |
Undo the power steering pump.
|
21. |
Move the power steering pump aside.
|
22. |
Remove the hose clips and hoses on the coolant pump inlet.
|
23. |
Detach the two longitudinal coolant pipes from the engine block.
|
24. |
Detach the two longitudinal coolant pipes from the coolant pump.
|
25. |
Slacken the bolt (by the turbo) securing the coolant pipe from the coolant pump.
|
26. |
Remove the coolant pipe from the coolant pump.
|
27. |
Undo the coolant pump retaining bolts.
|
28. |
Carefully work the pump free from the bracket and from the pump's connecting piece on the engine block.
|
29. |
Remove the connecting piece from the engine block and inspect its seals, Change the seals as necessary.
|
To fit |
Note | ||
Spray the connectors with Kontakt 61 contact cleaner, part No. 30 04 520. |
1. |
Fit the connecting piece to the engine block. Coat seals with Gleitmo 805, part. No. 30 06 442.
|
2. |
Fit the coolant pump.
Tightening torque: 22 Nm (16.2 lbf ft) |
3. |
Fit and tighten the coolant pipe to the coolant pump and by the turbo.
Tightening torques: Banjo bolt, turbo: 25 Nm (18.4 lbf ft) Banjo bolt, coolant pump: 20 Nm (14.7 lbf ft) |
4. |
Fit the two longitudinal coolant pipes to the coolant pump.
Tightening torque: 10 Nm (7.4 lbf ft) |
5. |
Fit the two longitudinal coolant pipes to the engine block.
|
6. |
Fit the hose clips and hoses to the coolant pump inlet.
|
7. |
Fit the power steering pump.
Tightening torque: 24 Nm (17.7 lbf ft) |
8. |
Extract the plug from the turbo inlet and then fit the intake pipe.
Tightening torques: V-clamp 3 Nm (2 lbf ft) |
9. |
Reconnect the vent hose.
|
10. |
Fit the exhaust manifold heat shield.
Tightening torque: 20 Nm (15 lbf ft) |
12. |
Fit the hoses to the turbo's wastegate valve.
|
13. |
Fit the engine lifting eye.
|
14. |
Plug in the boost pressure control valve connector.
|
15. |
Fit the crankcase breather pipe, fastened to the turbo intake pipe, and the camshaft cover.
Tightening torques: Crankcase breather pipe 24 Nm (18 lbf ft) |
16. |
Fit the multigroove V-belt and tension it with the belt tensioner. Use the pull bar part no. 83 95 254.
|
17. |
Fit the air hose and mass air flow sensor.
|
18. |
Plug in the mass air flow sensor connector.
|
19. |
Switch off the A/C or ACC. Fill with coolant to the MAX level. Refer to
Coolant
for mixtures. Do not forget to close the drain plug on the radiator first. Close the expansion tank lid.
|
20. |
Start the engine and run unloaded until warm at varying engine speeds until the radiator fan starts.
|
21. |
Turn off the engine and top up to the MAX level.
|
22. |
Inspect the system for possible leaks.
|
23. |
Raise the car.
|
24. |
Fit the lower front cover.
|
25. |
Lower the car to the floor.
|