Final dismantling and finishing measures
|
|
Final dismantling and finishing measures
|
|
Cleaning, Acrylate Latex (Not US/CA)
|
Warning
|
|
Safety information
|
|
Make sure that the room is adequately ventilated. Avoid contact with skin or mucous membranes. Use protective gloves. It is wise and recommended to use safety goggles. It is absolutely forbidden to apply detergent using a spray gun as this produces a mist. Never store detergent in bottles or containers without labelling them first with information on the manufacturer and type of detergent.
|
|
Remedial action if detergent gets into eyes
|
|
Wash out the detergent immediately. Keep the eyelids apart as much as possible. Rinse the eyes with plenty of water for at least 15 minutes. Then see a doctor immediately.
|
|
Poisonous!
|
|
If the substance has been swallowed and the person is conscious: Give the person large amounts of water to drink or a couple of glasses of milk.
Do not
induce vomiting. Seek medical help immediately.
|
|
Remedial action if splashed on skin
|
|
Take off clothing that has been splashed. Wash the skin thoroughly with soap and plenty of water.
|
|
|
|
|
|
The protective film for the paintwork (paint protector) must be removed by dissolving it with a special detergent, Tempro 75 Remover.
|
•
|
Tempro 75 Remover 10 litres - 30 02 482 25 litres - 30 02 490
|
|
•
|
High-pressure power washer
|
Consumption per car wash is about 0.3-0.5 litres of concentrated Tempro 75 Remover, equivalent to about 3-5 litres of diluted detergent.
|
Important
|
|
Tempro 75 Remover is a high-alkaline product (high pH). It should be used only on bodywork surfaces to which paint protector has been applied.
|
|
|
|
1.
|
Mix Tempro 75 Remover with hot water to a concentration of 2-4%. If water having a lower temperature is used to rinse off Tempro 75 Remover and the paintwork protector (see point 5), the concentration should be higher (but not more than 15%).
|
|
2.
|
Flush loose dirt off the car with a high-pressure power washer.
|
|
3.
|
Wet all parts of the bodywork covered by paint protector with Tempro 75 Remover, using a spray gun or the high-pressure power washer. The car should be at room temperature to ensure that the paint protector will be dissolved.
|
|
4.
|
Allow Tempro 75 Remover to act for about three minutes. Note that it must not be allowed to dry. If it does, apply additional Tempro 75 Remover.
|
|
5.
|
Rinse off the Tempro 75 Remover and the paint protector under high pressure with hot water (but not hotter than +60 °C).
|
|
6.
|
Remove any remaining paint protector using a sponge and Tempro 75 Remover.
|
|
7.
|
Wash the car, using a car shampoo.
|
General
RAPGARD paint protector may be left on the car for a maximum of three months and then it must be removed.
The date of manufacture of the car is on the vehicle card (422 indicates week 42 day 2), see illustration.
Illustration: Vehicle card
Removing
Removal of the RAPGARD paint protector must be carried out within the temperature range 0 to +35°C, +20°C being the most suitable temperature. If the body and the ambient temperature is above +35°C, park the car in the shade or cool it down with water until the body has reached a suitable temperature.
|
Important
|
|
Adhesive residue may fasten to the paintwork at high temperatures.
|
|
|
The Rapgard paint protector must be removed at least 48 hours before the car is shown to a customer so that any swelling has time to go down.
|
1.
|
Loosen the corners of the plastic film. Use hands only,
no tools
|
|
2.
|
Grip the plastic film as close as possible to the bodywork.
|
|
3.
|
Pull off parallel to the body surface at an even rate,
do not jerk
.
|
|
4.
|
Wash the car with water and dry it
|
|
5.
|
Make sure there is no adhesive residue remaining. If there is, remove it with petroleum spirit (low-aromatic petroleum hydrocarbon) or Iso propanol (Iso propyl alcohol). Use these sparingly and for short periods only.
|
When the plastic film and any adhesive residue has been removed the paintwork may have swelled. This is normally temporary and will disappear within 48 hours.
|
2.
|
Use concentrated washer fluid to clean all the windows and remove all residual grease from the windscreen and wiper blades.
|
|
3.
|
Remove transit and storage protection from doors, floor and seats. Remove also the rubber grommets that have secured the floor protection to the guide pins for additional carpets. Inspect the interior of the car for spots and stains and remove any you find.
|
Warning
|
|
The protective plastic must be removed before the car is handed over to the customer as protective plastic in the car does not meet the requirement of inflammability (legal requirement).
|
|
|
|
|
|
|
Warning
|
|
Make sure that the rear-seat backrests are properly secured.
|
|
|
|
|
|
Clean any dirt spots on plastic surfaces with soap and lukewarm water. Rinse the surfaces with clean water before drying.
|
Important
|
|
Vinyl sprays and the like must never be used as they could be the cause of a film forming on the windscreen and seriously reducing visibility.
|
|
|
|
|
4.
|
Clean rubber mouldings, tyre sidewalls and bumpers.
|
|
5.
|
Inspect the car, remove spots and stains. If necessary, polish the car.
|
