SAAB WIS ONLINE

Ventilation fan control (V6)

Ventilation fan control (V6)

To remove


1. Put the recirculation flap in OFF position and the ignition in LOCK.


2. Remove the glove box and side trim on the centre console, see Glove box .


3. Loosen the two front connectors above the filter cartridge.

Unplug the contacts from the plate and cut the cable tie.

4. Remove the wiper arms with special tool 85 80 144 Puller, windscreen wiper arm .


5. Remove the rubber seals from the wiper spindles.

6. Loosen the rubber moulding along the edge of the bulkhead in the middle only. Leave the outer clips in place.

7. Loosen the cover over the bulkhead partition space (fastened with clips) by lifting it carefully forwards so that it is released from the windscreen.

Move the wire to the bonnet to one side.

Note

Take care when remove the clips.


8. Loosen the clips holding the front edge of the water shield with a screwdriver. Lift off the water shield.


9. Remove the wiper unit and unplug the connector, 4 bolts.

10. Remove the stay to the right of the frame around the ventilation fan.

11. Remove the frame around the ventilator fan, 2 clips and 2 nuts on the front edge.


12. Remove the wiper arm bracket over the ventilation fan, 3 bolts.

13. Free the wiring harness from the cover over the ventilation fan (fastened with clips).

14. Remove the cover over the ventilator fan, 2 bolts on front edge and 2 bolts on rear edge. Unplug the fan connector. Pull the connector out of the hole in the cover.

15. Move the ventilation fan to the side and lift it out.

16. From the RH side, pull up the wiring harness including rubber seal into the fan housing.


Note

Make a note of the position of the wiring harness.


17. Remove the lower panel from the driver's side, 3 screws.


18. Remove the data link connector, 2 screws, and detach the leads to the floor lighting.

19. Detach the accelerator cable from the accelerator pedal.


20. Remove the accelerator panel, 2 nuts.

21. Remove the water shield over the ventilation fan control.

22. Remove the ventilation fan control and pull out the wiring harness.



To fit



1. Fit the ventilation fan control with water shield.

2. Pull out the wiring harness of the fan housing.

3. Fit the accelerator panel, 2 nuts.


4. Refit the accelerator cable.

5. Attach the connector to the floor lighting.

6. Fit the lower panel with air duct.


7. Fit the data link connector (2 bolts).

8. Insert the ventilation fan from one side of the bulkhead partition space.


9. Put the cover in place.

10. Insert the ventilation fan wiring harness on the RH side of the cover. Note the foam seal in the hole.

11. Fit the cover over the ventilation fan.

12. Fasten the wiring harness to the cover.

13. Insert the wiring harness on the right-hand side of the fan housing into the cabin and fit the rubber seal.

14. Fit the wiper arm bracket over the ventilation fan, 3 bolts.


15. Fit the frame around the ventilation fan, 2 clips and 2 nuts.

Make sure the gasket is positioned correctly.

16. Fit the stay to the right of the ventilation fan frame.

17. Fit the wiper unit, 4 bolts, and attach the connector.


18. Fit the water shield (fastened with 3 clips on the front edge).

19. Insert the cover over the bulkhead partition space from the rear, against the windscreen. Hold the wire to the bonnet to one side and then place it in its groove. Be careful when fitting the clips at the windscreen.


Note

Take care when remove the clips.


20. Fit the rubber strip on the front edge of the bulkhead.

21. Fit the rubber seals on the wiper spindles.

22. Fit the wiper arms.

23. Fit the contacts on the plate above the filter and fixate the wiring harness with a cable tie.


24. Plug in the connectors above the filter.


25. Fit the glove box and side trim on the centre console, see Glove box .