Fuel tank
| Fuel tank | 
| 
 | ||||||||||||||||||||||
| To remove | 
Drain the tank if the fuel level is above 1/4 full tank.
| 1. | Raise the rear seat cushion and fold back the carpet.   | |
| 2. | Remove the fuel pump cover. | |
| 3. | Undo the upper connector and the connector for the tank pressure sensor. 
 | ||||||||||
| 4. | Carefully loosen the check valves and fuel lines from the pump. The check valves are fastened to the pump with quick-release couplings. | |
| 5. | Undo the quick-release couplings for the vent hose, use special tool 83 95 261. | |
| 6. | Release the handbrake to make it easier to disconnect the handbrake cable later. | |
| 7. | Raise the car. | |
| 8. | Dismantle the rear exhaust pipe section.   | |
| 9. | Cut the cable tie securing the cables.   | |
| 10. | Unplug and detach the connector to the shut-off valve. | |
| 11. | Loosen the vent device from its holder with a screwdriver. | |
| 12. | Disconnect the vent device quick-release coupling from the tank in the following way.   | |
| 12.a. | Press in the connector towards the tank in the direction of the connection. | 
| 12.b. | Pinch the ring so that the catches go up. | 
| 12.c. | Detach the connection by pulling it away from the tank. | 
| 13. | Cut the cable tie securing the cables to the filler pipe.   | |
| 14. | Disconnect the vent pipe quick-release coupling with special tool 83 95 261. | |
| 15. | Undo the plastic screw. | |
| 16. | Loosen the hose clip and carefully detach the filler hose. | |
| 17. | Detach both handbrake cables at the handbrake lever.   | |
| 18. | Remove the rubber straps securing the handbrake cables | |
| 19. | Place a pillar jack under the tank.   | |
| 20. | Bend away the handbrake cables. | |
| 21. | Undo the front bolts on the straps securing the tank and carefully lower the tank. | |
| 21.A. | Carry out steps 22-25 when changing the tank. | 
| 22. | Remove the evaporative emission canister.   | |
| 23. | Remove the pressure sensor. | |
| 24. | Remove the fuel pump, see “Fuel system, Adjustment/replacement, Fuel pump”  . | |
| 25. | Remove the heat shield. | |
| To fit | 
 
    
    | 1. | Fit the heat shield. | |
| 2. | Fit the fuel pump, see “Fuel system, Adjustment/replacement, Fuel pump”  . | |
| 3. | Fit the pressure sensor. | |
| 4. | Fit the evaporative emission canister. | |
| 5. | Place the tank on a pillar jack. | |
| 6. | Carefully jack up the tank.   | |
| 7. | Place the handbrake cables in the tank recesses. | |
| 8. | Lift up the tank completely and fasten the straps. | |
| 9. | Attach the handbrake cables.   | |
| 10. | Fasten the rubber straps that keep the handbrake cables in place. | |
| 11. | Fit the filler pipe vent hose.   
 | |||||||
| 12. | Secure the cable to the filler pipe with a cable tie. | |
| 13. | Fit the rear section of the exhaust pipe   | |
| 15. | Fit the vent device and secure the cable with a cable tie. | |
| 16. | Lower the car to the floor. | |
| 17. | Apply acid-free Vaseline to the O-rings. Spray with Kontakt 61 and plug in the connector and connect the fuel lines.   | |
| 18. | Plug in the pressure sensor connector. | |
| 19. | Plug in the purge connector. | |
| 20. | Fit the cover and replace the carpet. | |
| 21. | Lower the seat cushion. | |

 Warning
                Warning
                
        
		