Bus messages, DICE
| Bus messages, DICE |
For a further description of the car's bus system, see System overview, bus and diagnostics communication, petrol and System overview, bus and diagnostics communication, diesel .
| DICE uses the following information |
|
Information
|
Value/Units
|
Off
|
The value depends on the following sensor input, signal or function
|
|
LH rear light
|
ON/OFF
|
TWICE
|
The control module input is supplied with current from the light switch. DICE uses the information for the instrument lighting.
|
|
RH rear light
|
ON/OFF
|
TWICE
|
The control module input is supplied with current from the light switch. DICE uses the information for the instrument lighting.
|
|
Driver's door
|
OPEN/CLOSED
|
TWICE
|
Door switch. DICE uses the information to turn on/off the interior lighting.
|
|
Passenger's door
|
OPEN/CLOSED
|
TWICE
|
Door switch. DICE uses the information to turn on/off the interior lighting.
|
|
LH Rear Door
|
OPEN/CLOSED
|
TWICE
|
Door switch. DICE uses the information to turn on/off the interior lighting.
|
|
RH Rear Door
|
OPEN/CLOSED
|
TWICE
|
Door switch. DICE uses the information to turn on/off the interior lighting.
|
|
Boot lid
|
OPEN/CLOSED
|
TWICE
|
Door switch. DICE uses the information to turn on/off the luggage compartment lighting.
|
|
Hazard flashers
|
ON/OFF
|
TWICE
|
Anti-theft alarm function and central locking function. DICE uses the information to activate/deactivate the hazard flashers for the car's anti-theft alarm.
|
|
A/C
|
ON/OFF
|
ACC
|
AUTO selected and outside temperature (bus from SID). DICE uses the information to turn on/off the car's A/C function.
|
|
Electrically heated rear window
|
ON/OFF
|
ACC
|
ACC sends A/C (ON/OFF).
ON is sent when ECON is not selected, outside temperature exceeds 5°C and fan speed is lowest. This value is used by DICE. Note that there are several excluding conditions in DICE. Note: Because the outside temperature value is not permitted to rise unless vehicle speed exceeds 30 km/h, A/C will not be requested if the outside temperature was under 5°C before the car was driven into the workshop (See activation: Outside temperature 20°C). |
|
Vehicle speed
|
km/h
|
MIU
|
Wheel speed, rear left (cable from ABS). DICE uses the information for the intermittent wiper function and for the car's radiator fan system.
|
|
Rheostat level
|
0-100%
|
SID
|
Rheostat control module input. DICE uses the information to control the brightness of the instrument and control lighting.
|
|
Rheostat Night Panel
|
0-100%
|
SID
|
Rheostat control module input, reduced internally by a fixed value. DICE uses the information to control the brightness of button illumination when NIGHT PANEL is active.
|
|
Night Panel
|
YES/NO
|
SID
|
Button. DICE uses the information on whether NIGHT PANEL is activated or deactivated.
|
|
Display lighting
|
0-100%
|
SID
|
Rheostat control module input or light sensor. DICE uses the information to control the brightness of the display.
|
|
Outdoor temperature
|
°C
|
SID
|
Outside temperature sensor, control module adjustment. DICE uses the information to control the radiator fan and A/C.
|
|
Engine has started
|
ON/OFF
|
Trionic (petrol) ECM (diesel)
|
Crankshaft sensor. DICE uses the information to control the radiator fans.
|
|
Coolant temperature
|
-40-215°C
|
Trionic (petrol) ECM (diesel)
|
Engine coolant temperature sensor. DICE uses the information to control the radiator fan and A/C systems.
|
|
Wheel speed RL
|
0-300 km/h
|
TC/ABS
|
RL wheel speed sensor.
|
|
RHD
|
YES/NO
|
|
|
|
Washer fluid level low
|
YES/NO
|
SID
|
The washer fluid level sensor. DICE will not start the headlamp washer pump if the fluid level is low.
|
|
Diagnostics
|
|
Tech 2
|
See Bus and diagnostics communication
|
| DICE sends the following information |
|
Information
|
Value/Units
|
Used by
|
The value depends on the following sensor input, signal or function
|
|
A/C request
|
ON/OFF
|
Trionic (petrol) ECM (diesel)
|
DICE transmits the A/C request, unit ON/OFF. This value is used in air mass regulation, compensation, to compensate for increased load. The control module also activates the A/C relay.
|
|
A/C pressure, high-pressure side
|
0-30 bar
|
Trionic (petrol) ECM (diesel)
|
DICE transmits the pressure, unit bar. This value is used in air mass regulation, compensation, to calculate load increase before the A/C compressor is activated.
|
|
Current consumption
|
A
|
Trionic (petrol) ECM (diesel)
|
DICE transmits the estimated current consumption of the electrically heated rear window and radiator fan just before they are activated, unit A. This value is used in air mass regulation, compensation, to compensate for load increase.
|
|
Reverse gear selected
|
YES/NO
|
PMM, Trionic, SPA
|
DICE sends reverse gear selected, unit ON/OFF. This value is used by the engine control system to determine if first gear or reverse gear is engaged as the gear ratio does not sufficiently differentiate between these gears. PMM uses this information to set the rear-view mirror and door mirrors.
|
|
Position lights
|
ON/OFF
|
MIU, SID
|
Rear light RH or LH (bus value from TWICE). MIU uses the information to turn on/off the marker light indicator on the main instrument panel.
|
|
Rear fog light
|
ON/OFF
|
MIU
|
Activation by the control module of the output to the fog light. MIU uses the information to turn on/off the rear fog light indicator on the main instrument panel.
|
|
LH direction indicators repeater
|
ON/OFF
|
MIU, SID
|
Activation by the control module of the output to the lamps. MIU uses the information to indicate activated LH direction indicators with control lamp on the main instrument panel.
SID uses the information for acoustic indication of activated direction indicators “tick-tack”. |
|
RH direction indicators repeater
|
ON/OFF
|
MIU, SID
|
Activation by the control module of the output to the lamps. MIU uses the information to indicate activated RH direction indicators with control lamp on the main instrument panel.
SID uses the information for acoustic indication of activated direction indicators “tick-tack”. |
|
Rear fog light faulty
|
YES/NO
|
SID
|
Control module current measurement of the output to the fog lamp. SID uses the information to display CHECK messages.
|
|
Sound
|
Sound information
|
SID
|
Control module programming, seat belt switch and driver/passenger door open (bus from TWICE). SID uses the information to generate an acoustic warning.
|
|
Electrically heated rear window, confirmation
|
ON/OFF
|
ACC
|
Control module activation of relay output to rear window heater. ACC uses the information to confirm that the rear window heating is active.
When ON, the button's symbol shows in the display. |
|
VIN
|
VIN
|
Audio
|
Control module programming. Audio uses the information for the system's anti-theft protection.
|
|
Ignition +B
|
ON/OFF
|
Audio, TWICE
|
Ignition switch. Informs Audio and TWICE of the position of the ignition switch.
|
|
Ignition +15
|
ON/OFF
|
TWICE
|
Ignition switch. Informs TWICE of the position of the ignition switch.
|
|
Ignition +54
|
ON/OFF
|
TWICE
|
Ignition switch. Informs TWICE of the position of the ignition switch.
|
|
Ignition +50
|
ON/OFF
|
TWICE, ACC
|
Ignition switch. Informs TWICE of the position of the ignition switch.
|
|
Radiator fan
|
ON/OFF
|
|
|
|
Battery voltage
|
6-16V
|
|
|
|
Diagnostics
|
|
Tech 2
|
See Bus and diagnostics communication
|
This project is supported by memberships and donations. If you use this site, please consider Joining SCNA and/or making a donation.
Our Friends
