SAAB WIS ONLINE

"Activate" menu

"Activate" menu

Note

When a system function is activated with the diagnostics tool, the control module executes a command which is not normal from a functional point of view. In activation mode the diagnostics tool checks the control module and the activation command should therefore be used with discrimination. An activated function will always be reset when you leave the activation mode and continue in the diagnostics tool's menu.

Always clear any diagnostic trouble codes that may have been generated in the transmission system or any other system when you have finished your work.


Important

Activation mode can only be entered in selector lever position N. In other selector lever positions the diagnostics tool's display will show SHIFT TO N AND THEN PRESS ENTER. All activation commands can be cancelled by pressing Exit.


Activate

Condition Activation

Description

Usage

Solenoid S1

Ignition ON

The control module is energising solenoid S1

If in working order the solenoid will click. A stethoscope should be used.

Solenoid S1

requested status

Ignition ON

ON/OFF

Energizes the solenoid by feeding B+ to the relevant pin. The vehicle speed must be 0 km/h and the selector lever in position P or N.

Solenoid S2

Ignition ON

The control module is energising solenoid S2

If in working order the solenoid will click. A stethoscope should be used.

Solenoid S2

requested status

Ignition ON

ON/OFF

Energizes the solenoid by feeding B+ to the relevant pin. The vehicle speed must be 0 km/h and the selector lever in position P or N.

Solenoid S3

Ignition ON

The control module is energising solenoid S2

If in working order the solenoid will click. A stethoscope should be used.

Solenoid S3

requested status

Ignition ON

ON/OFF

Energizes the solenoid by feeding B+ to the relevant pin. The vehicle speed must be 0 km/h and the selector lever in position P or N.

Solenoid S4

Ignition ON

The control module is energising solenoid S2

If in working order the solenoid will click. A stethoscope should be used.

Solenoid S4

requested status

Ignition ON

ON/OFF

Energizes the solenoid by feeding B+ to the relevant pin. The vehicle speed must be 0 km/h and the selector lever in position P or N.

Solenoid S5

Ignition ON

The control module is energising solenoid S2

If in working order the solenoid will click. A stethoscope should be used.

Solenoid S5

requested status

Ignition ON

ON/OFF

Energizes the solenoid by feeding B+ to the relevant pin. The vehicle speed must be 0 km/h and the selector lever in position P or N.

Solenoid SLS

Ignition ON

The control module is energising solenoid SLS with a 300 Hz PWM signal

When functioning properly the energized solenoid makes a soft humming noise. Use a stethoscope.

Solenoid SLS

Requested current

Ignition ON

mA

Energizes the solenoid with a variable current. The vehicle speed must be 0 km/h and the selector lever position P or N.

Solenoid SLU

Ignition ON

The control module is energising solenoid SLU with a 300 Hz PWM signal

When functioning properly the energized solenoid makes a soft humming noise. Use a stethoscope.

Solenoid SLU

Requested current

Ignition ON

mA

Energizes the solenoid with a variable current. The vehicle speed must be 0 km/h and the selector lever position P or N.

Solenoid SLT

Ignition ON

The control module is energising solenoid SLT with a 300 Hz PWM signal

When functioning properly the energized solenoid makes a soft humming noise. Use a stethoscope.

Solenoid SLT

Requested current

Ignition ON

mA

Energizes the solenoid with a variable current. The vehicle speed must be 0 km/h and the selector lever position P or N.

Reset Adaption

Ignition ON





SPORT Lamp

Ignition ON





WINTER Lamp

Ignition ON





CHECK GEARBOX Lamp

Ignition ON





MIL Request

Ignition ON





Zero the adaptation value

Ignition ON

OK

The adaptive values must be reset to the basic (initial) value after changing the transmission, throttle housing or the TCM. If this is not done the transmission can be damaged.