Body dimensions
These measurements are suitable for determining if the car should be mounted in an alignment bench.
Pos
|
Dimension, mm
|
Measuring points
|
1
|
4508
|
Total length. Front bumper member - Rear bumper bracket
|
2
|
885±1
|
Hole for rubber buffer (*) - Hole for plastic clip, windscreen cover (*)
|
3
|
1010±1
|
Hole for rubber buffer (*) - Front hole in windscreen wiper mechanism bracket (*)
|
4
|
1593±1
|
Hole for rubber buffer (*) - Hole for plastic clip, windscreen cover, diagonal (*)
|
5
|
1240±1
|
Hole for rubber buffer RH side (*) - Hole for rubber buffer LH side (*)
|
6
|
642±1
|
Outer rear hole, MacPherson strut (*) - Front hole in holder. windscreen wiper mechanism (*)
|
7
|
1232±1
|
Outer rear hole, MacPherson strut, RH side (*) - Outer rear hole, MacPherson strut, LH side (*)
|
8
|
1429±1
|
Lower section A-pillar - Upper section A-pillar, diagonally
|
9
|
1499±1
|
Distance between weatherstrip ribs on top of door sill
|
(*) = dimension is measured from the centre of the hole.
Measurements, body rear, side
|
Pos
|
Dimension, mm
|
Measuring points
|
10
|
1102±1
|
Upper hole, front hinge (*) - Lower hole, rear hinge (*)
|
11
|
1146±1
|
Lower hole, front hinge (*) - Upper hole, rear hinge (*)
|
12
|
1006±1
|
Lower hole, rear hinge (*) - Upper hole, striking plate, rear door (*)
|
13
|
941±1
|
Upper hole, rear hinge (*) - Upper hole, striking plate, rear door (*)
|
14
|
1177±1
|
Distance between rear side panels, lower rear corner
|
15
|
1054±1
|
Distance between lower holes for bumper (*)
|
16
|
1237±1
|
Rear side panel, lower rear corner - Lower hole for bumper, diagonal (*)
|
(*) = dimension is measured from the centre of the hole.
Measurements, body B-pillar
|
Pos
|
Dimension, mm
|
Measuring points
|
17
|
1611±1
|
Elongated hole under seat-belt bolt (*) - Large hole at front of B-pillar under elongated hole for B-pillar trim retaining clip (*)
|
18
|
1504±1
|
Distance between holes RH - LH side (*)
|
(*) = dimension is measured from the centre of the hole.
Illustration A shows the correct measuring direction for measurements 19, 20, 26 and 27
Illustration B shows the incorrect measuring direction for measurements 19, 20, 26 and 27
Pos
|
Dimension, mm
|
Measuring points
|
19
|
1528±1
|
Hole in wheel housing, behind collision box (*) - Hole in floor reinforcement, inner hole, diagonal (*). Fig. A shows correct measuring direction.
|
20
|
1171±1
|
Hole in wheel housing, behind collision box (*) - Hole in floor reinforcement, inner hole (*). Fig. A shows correct measuring direction.
|
21
|
964±1
|
Hole in wheel housing, behind collision box RH side (*) - Hole in wheel housing, behind collision box LH side (*).
|
22
|
1000±1
|
Hole in floor reinforcement, inner hole RH side (*) - Hole in floor reinforcement, inner hole LH side (*).
|
23
|
1350±1
|
Distance between ribs underneath door sill (refers to max. distance between pressings).
|
24
|
1258±1
|
Hole in frame member ahead of rear axle mounting RH side (*) - Hole in frame member ahead of rear axle mounting LH side (*)
|
25
|
1053±1
|
Hole in frame member ahead of collision box, rear bumper abutment RH side (*) - Hole in frame member ahead of collision box, rear bumper abutment LH side (*)
|
26
|
1756±1
|
Hole in frame member ahead of rear axle mounting (*) - Hole in frame member ahead of collision box, rear bumper abutment diagonal (*). Fig. A shows correct measurement direction.
|
27
|
1327±1
|
Hole in frame member ahead of rear axle mounting (*) - Hole in frame member ahead of collision box, rear bumper abutment (*). Fig. A shows correct measuring direction.
|
(*) = dimension is measured from the centre of the hole.
Measurements, body rear 5D
|
Pos
|
Dimension, mm
|
Measuring points
|
28
|
1272±1
|
Square hole for scuff plate clip (*) - Inner radius, top of luggage compartment opening where dimension is greatest.
|
29
|
1320±1
|
Upper hole for bumper (*) - Outer hole for tailgate hinge (*)
|
(*) = dimension is measured from the centre of the hole.