DTC P2227, P2228, or P2229 (LAU)
|
|
DTC P2227, P2228, or P2229 (LAU)
|
DTC P2227
Barometric Pressure (BARO) Sensor Performance
DTC P2228
Barometric Pressure (BARO) Sensor Circuit Low Voltage
DTC P2229
Barometric Pressure (BARO) Sensor Circuit High Voltage
|
Circuit/System Description
|
The barometric pressure (BARO) sensor responds to changes in altitude and atmospheric conditions. This gives an indication of atmospheric pressure to the engine control module (ECM). The ECM uses this information to calculate fuel delivery. The BARO sensor is located within the controller and is not serviced as a separate unit. The BARO sensor provides a voltage signal to the ECM relative to the atmospheric pressure changes. The ECM monitors the BARO sensor signal for a voltage outside of the normal range.
|
Conditions for Running the DTC
|
P2227
|
•
|
Before the ECM can report DTC P2227 failed, DTCs P0100, P0101, P0102, P0103, P0111, P0112, P0113, P0114, P0121, P0122, P0123, P0221, P0222, P0223, P0236, P0237, P0238, P2228, and P2229 must run and pass.
|
|
•
|
The engine is operating.
|
|
•
|
The engine speed is less than 1,120 RPM.
|
|
•
|
The Throttle Position Sensor parameter is less than 10%.
|
|
•
|
DTC P2227 runs continuously when the above conditions are met.
|
P2228 or P2229
|
•
|
The DTCs run continuously when the above condition is met for 0.2 s.
|
|
Conditions for Setting the DTC
|
P2227
|
•
|
The ECM detects that the BARO sensor signal plus a calibrated threshold is less than the boost pressure sensor signal plus a calibrated threshold for more than 9 s.
OR
|
|
•
|
The ECM detects that the BARO sensor signal plus a calibrated threshold greater than the boost pressure sensor signal plus a calibrated threshold for more than 9 s.
OR
|
|
•
|
The ECM detects that the BARO pressure changed greater than 5 kPa (0.7 psi) within 20 s.
OR
|
|
•
|
The ECM detects that the BARO pressure changed greater than 10 kPa (1.5 psi) since the last ignition cycle.
|
P2228
|
•
|
The ECM detects that the BARO sensor voltage is less than 0.20 V for 0.5 s.
OR
|
|
•
|
The ECM detects that the BARO sensor signal is less than 45 kPa (6.5 psi) for 2 s
|
P2229
|
•
|
The ECM detects that the BARO sensor voltage is greater than 4.8 V for 0.5 s.
OR
|
|
•
|
The ECM detects that the BARO sensor signal is greater than 115 kPa (16.7 psi) for 2 s.
|
|
Action Taken When the DTC Sets
|
DTCs P2227, P2228, and P2229 are Type B DTCs.
|
Conditions for Clearing the MIL/DTC
|
DTCs P2227, P2228, and P2229 are Type B DTCs.
Schematic Reference
Engine Controls Schematics
Connector End View Reference
Component Connector End Views
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References
for scan tool information
|
Circuit/System Verification
|
|
1.
|
Start the engine. Check the DTC Info with a scan tool. DTCs P2227, P2228 or P2229 should not set.
|
|
2.
|
Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
|
|
1.
|
Inspect the atmospheric vent on the K20 ECM case for one of the following conditions:
|
|
|
•
|
Moisture in the vent inlet
|
|
|
•
|
Debris in the vent inlet
|
|
2.
|
If a condition exists, attempt to clean or dry the atmospheric inlet.
|
|
3.
|
Start the engine. Check the DTC Info with a scan tool. DTCs P2227, P2228 or P2229 should not set.
|
|
4.
|
If DTC P2227, P2228, or P2229 sets, replace the K20 ECM.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
Control Module References
for ECM replacement, setup, and programming
