DTC B1529
| DTC B1529 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC B1529 03
Control Module Voltage Reference Output 5 Circuit Low Voltage
DTC B1529 07
Control Module Voltage Reference Output 5 Circuit High Voltage
| Diagnostic Fault Information |
Electrical DTCs
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
12V Reference
|
B1529 03, B1405 03
|
1
|
B1529 07
|
B1529 07
|
|
Steering Wheel Control Switch Signal
|
1
|
1
|
B3622 07
|
-
|
|
1. Steering Wheel Controls Inoperative
|
||||
| Circuit/System Description |
The body control module (BCM) supplies voltage to the steering wheel control switches and monitors the return signal. Each switch state is associated to a set resistance value and when pressed a specific voltage drop occurs across the resistor unique to the switch. The BCM identifies the switch selection and activates the feature.
| Conditions for Running the DTC |
| • |
The system voltage is between 9-16 V.
|
|
| • |
The ignition is ON.
|
|
| Conditions for Setting the DTC |
B1529 03
| • |
The BCM detects a short to ground in the 12 V reference circuit.
|
|
| • |
The above condition is present for greater than 30 s.
|
|
B1529 07
| • |
The BCM detects a short to voltage in the 12 V reference circuit.
|
|
| • |
The above condition is present for greater than 30 seconds.
|
|
| Action Taken When the DTC Sets |
The BCM will ignore switch inputs.
| Conditions for Clearing the DTC |
| • |
The condition responsible for setting the DTC no longer exists.
|
|
| • |
A history DTC will clear once 100 consecutive malfunction free ignition cycles have occurred.
|
|
| Reference Information |
Schematic Reference
Steering Wheel Secondary/Configurable Control Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Steering Wheel Controls Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the X3 harness connector at the X85 Steering Wheel Air Bag Coil.
|
|
| 2. |
Ignition ON, test for greater than 11 V between the voltage reference circuit terminal 6 X3 male side and ground.
|
|
| 3. |
If less than the specified value, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
|
| 4. |
Test for greater than 11 V between the voltage reference circuit terminal 6 X3 male side and the signal circuit terminal 7 X3 male side.
|
|
| 5. |
If less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
|
| 6. |
Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module.
|
|
| 7. |
Test for infinite resistance between the signal circuit terminal 7 X3 male side at the X85 Steering Wheel Air Bag Coil and ground.
|
|
| 8. |
If less than the specified value, test the signal circuit for a short to ground.
|
|
| 9. |
If all circuits test normal, test or replace the S70R Steering Wheel Controls Switch - Right.
|
|
| Component Testing |
Static Test
| 1. |
Disconnect the harness connector at the X85 Steering Wheel Air Bag Coil.
|
|
| 2. |
Test the resistance between the terminals 6 X3 female side and 7 X3 female side of the X85 Steering Wheel Air Bag Coil.
|
|
| 3. |
If any of the resistance measurements for the individual switches are not within the specified resistance values, replace the S70R Steering Wheel Controls Switch - Right.
|
|
| Function Switch | Minimum Resistance Value | Maximum Resistance Value |
|
Volume Up
|
1.0 kΩ
|
1.4 kΩ
|
|
Volume Down
|
1.3 kΩ
|
1.7 kΩ
|
|
SRC ↑
|
1.7 kΩ
|
2.2 kΩ
|
|
SRC ↓
|
2.0. kΩ
|
2.8 kΩ
|
|
Source
|
2.8 kΩ
|
3.2 kΩ
|
|
Phone/Push to Talk
|
3.6 kΩ
|
4.0 kΩ
|
|
Hang Up/Audio Mute
|
5.1 kΩ
|
5.5 kΩ
|
|
No Switch Pressed
|
O.L.
|
O.L.
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for BCM replacement, setup, and programming.
This project is supported by memberships and donations. If you use this site, please consider Joining SCNA and/or making a donation.
Our Friends
