OnStar Button LED Malfunction
|
OnStar Button LED Malfunction
|
Diagnostic Fault Information
|
Circuit
|
Short to Ground
|
Open/High Resistance
|
Short to Voltage
|
Signal Performance
|
Keypad Supply Voltage
|
B2476 00
|
B2476 00
|
B2476 00
|
-
|
Keypad Green LED Control
|
1
|
1
|
2
|
-
|
Keypad Red LED Control
|
1
|
1
|
2
|
-
|
Keypad Signal
|
3
|
3
|
-
|
-
|
Inside Rearview Mirror Ground
|
-
|
1
|
-
|
-
|
1. OnStar® LED Inoperative
2. LED Illuminated At All Times
3. OnStar® Buttons Inoperative
|
The OnStar® status LEDs are located in the inside rear view mirror telematic button assembly. The green LED is illuminated when the system is ON and operating normally. When the green LED is green and flashing, it is an indication that a call is in progress. When the red LED is illuminated, a system malfunction is present. In the event there is a system malfunction and the OnStar® system is still able to make a call, the LED will flash red during the call. The OnStar® LEDs are controlled by the telematics communication interface control module via the keypad green LED control circuit and the keypad red LED control circuit.
Schematic Reference
OnStar Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
OnStar Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for scan tool information
Circuit/System Verification
|
Note
|
If the green LED is off with the Key on and the LED functions correctly when commanded with the scan tool, contact the OnStar Center to confirm the vehicle has a current subscription.
|
1.
|
Ignition ON, command the Green LED ON and OFF with a scan tool while observing the green LED on the A10 inside rear view mirror. The green LED should turn ON and OFF when commanded.
|
2.
|
Command the red LED ON and OFF with a scan tool while observing the red LED on the A10 inside rear view mirror. The red LED should turn ON and OFF when commanded.
|
1.
|
Ignition OFF, disconnect the harness connector at the A10 inside rear view mirror.
|
2.
|
Doors closed, courtesy lamps OFF, test for less than 10 Ω between the ground circuit terminal 5 and ground.
|
3.
|
If greater than the specified range, test the ground circuit for an open/high resistance.
|
4.
|
Ignition ON, command the green LED OFF with a scan tool. Test for less than 1 V between the control circuit terminal 6 and ground.
|
5.
|
If greater than the specified range, test the control circuit for a short to voltage. If the circuit tests normal, replace the K73 telematics communication interface control module.
|
6.
|
Command the green LED ON with a scan tool. Test for greater than 9 V between the control circuit terminal 6 and ground.
|
7.
|
If less than the specified range, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K73 telematics communication interface control module.
|
8.
|
Command the red LED OFF with a scan tool. Test for less than 1 V between the control circuit terminal 7 and ground.
|
9.
|
If greater than the specified range, test the control circuit for a short to voltage. If the circuit tests normal, replace the K73 telematics communication interface control module.
|
10.
|
Command the red LED ON with a scan tool. Test for greater than 9 V between the control circuit terminal 7 and ground.
|
11.
|
If less than the specified range, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K73 telematics communication interface control module.
|
12.
|
If all circuits test normal, replace the A10 inside rear view mirror.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.