DTC B3567
DTC B3567 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B3567 01
Info Display Select Switch Circuit Short to Battery
DTC B3567 02
Info Display Select Switch Circuit Short to Ground
DTC B3567 04
Info Display Select Switch Circuit Open
DTC B3567 59
Info Display Select Switch Circuit Protection Time-Out
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Driver Information Center Switch Signal
|
B3567 02
|
B3567 04
|
B3567 01
|
-
|
Driver Information Center Reset Switch Signal
|
1
|
1
|
1
|
-
|
Low Reference
|
-
|
B3567 04
|
-
|
-
|
1. Driver Information Center Switch Malfunction
|
Circuit/System Description |
The driver information center switch is a multiplexed switch. Battery power is provided to the driver information center switch via the instrument cluster. The driver information center switch signal circuit is pulled up to battery voltage in the instrument cluster. The instrument cluster also provides the driver information center switch with a low reference. The switch input to the instrument cluster is pulled low when a switch is activated. The driver information center switch is a momentary contact switch that connects a series of resistors in a resistor ladder format. The instrument cluster monitors the driver information center switch signal circuit to determine the driver information center switch inputs. Each switch state - Menu, UP, DOWN - corresponds to a certain resistance value. The instrument cluster determines the switch pressed by the voltage drop across the resistors.
Conditions for Running the DTC |
• |
The ignition is in OFF, ACCESSORY or RUN position.
|
• |
The system voltage is between 9-16 V.
|
Conditions for Setting the DTC |
B3567 01
The instrument cluster detects that the driver information center switch signal circuit is shorted to battery.B3567 02
The instrument cluster detects that the driver information center switch signal circuit is shorted to ground.B3567 04
The instrument cluster detects that the driver information center switch signal circuit is open.B3567 59
The instrument cluster detects that the driver information center switch is stuck.Action Taken When the DTC Sets |
The instrument cluster ignores the driver information center switch inputs.
Conditions for Clearing the DTC |
The DTC will become history if the instrument cluster no longer detects a malfunction.
Reference Information |
Schematic Reference
Instrument Cluster Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
• |
Instrument Cluster Description and Operation
|
• |
Driver Information Center (DIC) Description and Operation
|
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References
Circuit/System Verification |
Ignition ON, observe the scan tool Driver Information Center Switch parameter, while pressing and releasing the S78 Turn Signal/Multi-Function Switch Menu, UP, DOWN, and SET/CLR buttons. The reading should toggle between Menu, Up, Down, Clear and Inactive.
Circuit/System Testing |
1. |
Ignition OFF, disconnect the harness connector at the S78 Turn Signal/Multi-Function Switch.
|
2. |
Ignition OFF for more than 60 s, test for less than 10 Ω between the low reference circuit terminal 6 and ground.
|
3. |
If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the P16 Instrument Cluster.
|
4. |
Ignition ON, verify the scan tool Driver Information Center Switch parameter is Undefined.
|
5. |
If not Undefined, test the signal circuits terminal 5 and terminal 12 for a short to ground. If the circuit tests normal, replace the P16 Instrument Cluster
|
6. |
Ignition ON, install a 680 Ω resistance between the signal circuit terminal 12 and the low reference circuit terminal 6. Verify the scan tool Driver Information Center Switch parameter is Up.
|
7. |
If not Up, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the P16 Instrument Cluster.
|
8. |
Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal 5 and the low reference circuit terminal 6. Verify the scan tool Driver Information Center Switch is Menu.
|
9. |
If not Menu, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the P16 Instrument Cluster.
|
10. |
If all circuits test normal, test or replace the S78 Turn Signal/Multi-Function Switch.
|
Component Testing |
Static Test
1. |
Ignition OFF, disconnect the harness connector at the S78 Turn Signal/Multi-Function Switch.
|
2. |
Test for 8.5-9.1 kΩ between the signal terminal 12 and the low reference circuit terminal 6.
|
3. |
If not within the specified range, replace the S78 Turn Signal/Multi-Function Switch.
|
4. |
Test for 550-650 Ω between the signal terminal 12 and the low reference circuit terminal 6 while pressing the Up switch.
|
5. |
If not within the specified range, replace the S78 Turn Signal/Multi-Function Switch.
|
6. |
Test for 1.5-1.7 kΩ between the signal terminal 12 and the low reference circuit terminal 6 while pressing the Down switch.
|
7. |
If not within the specified range, replace the S78 Turn Signal/Multi-Function Switch.
|
8. |
Test for 3.3-3.7 kΩ between the signal terminal 12 and the low reference circuit terminal 6 while pressing the Reset switch.
|
9. |
If not within the specified range, replace the S78 Turn Signal/Multi-Function Switch.
|
10. |
Test for less than 5 Ω between the signal terminal 5 and the low reference circuit terminal 6 while pressing the Menu switch.
|
11. |
If greater than the specified value, replace the S78 Turn Signal/Multi-Function Switch.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Turn Signal Multifunction Switch Replacement
|
• |
Control Module References
|