DTC B1474
DTC B1474 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
has overviews of all diagnostic categories.
|
DTC Descriptor |
DTC B1474 02
Passenger Exterior Door Handle Switch Circuit Short to Ground
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Passenger Door Handle Switch Signal
|
B1474 02
|
1
|
1
|
-
|
Left Rear Door Handle Switch Signal
|
B1534 02
|
1
|
1
|
-
|
Right Rear Door Handle Switch Signal
|
B1535 02
|
1
|
1
|
-
|
Passenger Door Handle Switch Ground
|
-
|
1
|
1
|
-
|
Left Rear Door Handle Switch Ground
|
-
|
1
|
1
|
-
|
Right Rear Door Handle Switch Ground
|
-
|
1
|
1
|
-
|
1. Power Door Latch Malfunction
|
Circuit/System Description |
The right front exterior door handle switch signal circuit provides inputs to the keyless entry control module when the right front exterior door handle switch is activated. This input allows the keyless entry control module to detect a door open request. The keyless entry control module provides voltage to the right front exterior door handle switch via the right front door handle switch signal circuit. When the right front door handle is activated, the switch closes and the voltage signals from the keyless entry control module are pulled to ground.
Conditions for Running the DTC |
Battery voltage is between 9-16 V.
Conditions for Setting the DTC |
The keyless entry control module detects the right front exterior door handle switch signal circuit is shorted to ground or closed for more than 60 s.
Action Taken When the DTC Sets |
The keyless entry control module ignores inputs from the right front exterior door handle switch.
Conditions for Clearing the DTC |
• |
The DTC will be current for as long as the fault is present.
|
• |
When the fault is no longer present, the DTC will be a history DTC.
|
• |
A history DTC will clear after 50 ignition cycles.
|
Reference Information |
Schematic Reference
Door Lock/Indicator Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Power Door Locks Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for information on diagnostic tools
Circuit/System Verification |
Ignition ON, observe the scan tool keyless entry control module Exterior Passenger Door Handle Switch parameter while using the passenger door handle. The parameter should change between Active and Inactive.
Circuit/System Testing |
1. |
Ignition OFF, disconnect the harness connector at the B27P Door Handle Switch - Passenger Exterior.
|
2. |
Ignition ON, verify the scan tool Exterior Passenger Door Handle Switch parameter is Inactive.
|
3. |
If not the specified value, test the signal circuit terminal 2 for a short to ground. If the circuit tests normal replace the K84 Keyless Entry Control Module.
|
4. |
Install a 3 A fused jumper wire between the signal circuit terminal 2 and ground circuit terminal 1. Verify the scan tool Exterior Passenger Door Handle Switch parameter is Active.
|
5. |
If not the specified value, test the signal circuit terminal 2 for an open/high resistance. If the circuit tests normal replace the K84 Keyless Entry Control Module.
|
6. |
If all circuits test normal, test or replace the B27P Door Handle Switch - Passenger Exterior.
|
Component Testing |
Static Test
1. |
Ignition OFF, disconnect the harness connector at the B27P Door Handle Switch - Passenger Exterior.
|
2. |
With the switch in the open position, test for infinite resistance between the signal terminal 2 and the ground terminal 1.
|
3. |
If not the specified value, replace the B27P Door Handle Switch - Passenger Exterior.
|
4. |
With the switch in the closed position, test for less than 5 Ω between the signal terminal 2 and the ground terminal 1.
|
5. |
If greater than the specified range, replace the B27P Door Handle Switch - Passenger Exterior.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Front Side Door Outside Handle Replacement (Base)
|
• |
Control Module References
for keyless entry control module replacement, setup and programming
|