DTC B3205, B3210, B3215, or B3220
DTC B3205, B3210, B3215, or B3220 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
has overviews of all diagnostic categories.
|
DTC Descriptors |
DTC B3205 00
Driver Window Motor Malfunction
DTC B3205 39
Driver Window Motor Internal Malfunction
DTC B3205 42
Driver Window Motor Calibration Not Programmed
DTC B3205 4B
Driver Window Motor Circuit Calibration Not Learned
DTC B3210 00
Passenger Window Motor Malfunction
DTC B3210 39
Passenger Window Motor Internal Malfunction
DTC B3210 42
Passenger Window Motor Calibration Not Programmed
DTC B3210 4B
Passenger Window Motor Calibration Not Learned
DTC B3215 00
Left Rear Window Motor Malfunction
DTC B3215 39
Left Rear Window Motor Internal Malfunction
DTC B3215 42
Left Rear Window Motor Calibration Not Programmed
DTC B3215 4B
Left Rear Window Motor Calibration Not Learned
DTC B3220 00
Right Rear Window Motor Malfunction
DTC B3220 39
Right Rear Window Motor Internal Malfunction
DTC B3220 42
Right Rear Window Motor Calibration Not Programmed
DTC B3220 4B
Right Rear Window Motor Calibration Not Learned
Circuit/System Description |
The Body Control Module (BCM) monitors, receives and transmits serial data to each of the doors switches and window motors. When a window switch has been activated on the driver window switch, a signal is sent to the BCM which sends a signal to the appropriate window motor and the window motor will move in the direction commanded.
Conditions for Running the DTC |
• |
The ignition is in the ON position.
|
• |
Battery voltage must be between 9-16 V.
|
Conditions for Setting the DTC |
B3205 00, B3210 00, B3215 00, B3220 00
The BCM has detected that the compatibility code stored in the affected window motor does not match the compatibility code stored in the BCM.B3205 39, B3210 39, B3215 39, B3220 39
An internal malfunction has been detected by the BCM in the power window motor while commanding the window UP or DOWN.B3205 42, B3210 42, B3215 42, B3220 42
The BCM will automatically attempt to download the calibration program into the appropriate window motor (As will occur when the window motor has been replaced), if the first calibration program fails to load, the BCM will attempt to download the calibration program a second time. If this download fails, the BCM will set appropriate DTC.B3205 4B, B3210 4B, B3215 4B, B3220 4B
The BCM detects that a window motor is "not normalized" which will occur under the following conditions:• |
When the battery has been disconnected
|
• |
When the battery has been replaced
|
• |
When the door wiring harness has been disconnected
|
• |
When the window motor has been disconnected
|
Action Taken When the DTC Sets |
B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 39, B3220 39
The affected motor will be inoperative.B3205 4B, B3210 4B, B3215 4B, B3220 4B
The affected motor will not perform the express up or express down functions and the driver information center will display Open, then Close Driver Window or will display Open, then Close Passenger Window.Conditions for Clearing the DTC |
B3205 00, B3210 00, B3215 00, B3220 00
Installing a compatible window motor for that specific make and model vehicle.B3205 39, B3210 39, B3215 39, B3220 39
The appropriate window motor must be replaced before the DTC can be cleared.B3205 42, B3210 42, B3215 42, B3220 42
The appropriate window motor must be replaced before the DTC can be cleared.B3205 4B, B3210 4B, B3215 4B, B3220 4B
The appropriate window motor must be normalized before the DTC can be cleared.Reference Information |
Schematic Reference
Moveable Window Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Power Windows Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for information on diagnostic tools
Circuit/System Verification |
B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 00, B3215 39, B3215 42, B3220 00, B3220 39, B3220 42
1. |
Ignition ON, command the window motor UP and DOWN with a scan tool. The window motor should perform the UP and DOWN functions.
|
2. |
Replace the window motor with a window motor compatible for that specific make and model vehicle. |
Circuit/System Testing |
B3205 4B, B3210 4B, B3215 4B, B3220 4B
1. |
Ignition ON. Start with the window completely raised. Hold the relevant window switch depressed until the window is completely open. Hold the switch depressed another 5 seconds after the window is completely open. |
2. |
Pull the power window switch up until the window is fully closed and continue holding the switch up for approximately 5 seconds after the window is completely closed.
|
3. |
Command the window to express UP and express DOWN by pressing the window switch past the first detent and releasing and then pulling the window switch past the first detent and releasing. The window should perform the express UP and express DOWN functions.
|
4. |
If the appropriate window motor does not perform as specified and the DTC resets, replace the appropriate window motor.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Front Side Door Window Regulator Motor Replacement
|
• |
Rear Side Door Window Regulator Motor Replacement
|
• |
Control Module References
for information on BCM replacement, setup, and programming
|