DTC B3664
DTC B3664 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B3664 02
Sunroof Position Select Switch High Signal Circuit Short to Ground
DTC B3664 05
Sunroof Position Select Switch High Signal Circuit High Voltage/Open
DTC B3664 59
Sunroof Position Select Switch High Signal Circuit Protection Time-Out
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Sunroof Position Select Switch Control
|
B3664 02
|
B3664 05
|
B3664 05
|
--
|
Sunroof Position Select Switch Low Reference
|
-
|
1
|
1
|
-
|
1. Power Sunroof/Sunshade Malfunction
|
Circuit/System Description |
The sunroof position select switch is connected directly to the controller. The sliding glass switch provide detent positions for open, express open, off, close, and express close. The sunroof position select switch completes the circuit between two signals provided by the control module, a reference ground input and a pull-up voltage provided by an analog to digital switch input. The control switch places a different resistor ladder network in the circuit depending on the function selected.
Conditions for Running the DTC |
The ignition is ON.
Conditions for Setting the DTC |
B3664 02
The sunroof module has detected and reported via the LIN-Bus that the sunroof position select switch high signal circuit is shorted to ground.B3664 05
The sunroof module has detected and reported via the LIN-Bus that the sunroof position select switch high signal circuit is open or shorted to voltage.B3664 59
The sunroof module has detected and reported via the LIN-Bus that the sunroof position select switch high signal has been the same active position for 20 s after the glass has stopped moving in the requested direction due to reaching the end of the allowable motion.Action Taken When the DTC Sets |
DTC B3664 is stored in the body control module (BCM) memory.
Conditions for Clearing the DTC |
The BCM no longer detects a malfunction in the sunroof position select switch high signal circuit.
Reference Information |
Schematic Reference
Sunroof Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Sunroof Description and Operation (Spoiler System)
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing |
Note | ||
Because of the accessibility of the sunroof switch, perform the component testing before beginning the Circuit/System Testing. |
1. |
Ignition OFF, disconnect the harness connector at the S72 Sunroof Switch.
|
2. |
Test for less than 5 Ω between the ground circuit terminal 1 and ground.
|
3. |
If greater than the specified range, test the ground circuit for an open/high resistance.
|
4. |
Ignition ON, verify the scan tool sunroof slide switch is short to battery.
|
5. |
If not the specified value, test the signal circuit terminal 4 for a short to ground. If the circuit tests normal, replace the K61 Sunroof Control Module.
|
6. |
Install a 5 A fused jumper wire between the signal circuit terminal 4 and the ground circuit terminal 1. Verify the scan tool sunroof slide switch is short to ground.
|
7. |
If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K61 Sunroof Control Module.
|
8. |
If all circuits test normal, test or replace the S72 Sunroof Switch.
|
Component Testing |
Static Test
1. |
Ignition OFF, disconnect the harness connector at the S72 Sunroof Switch.
|
2. |
Test for 3.6-3.7 kΩ between the switch terminals 1 and 4.
|
3. |
If not within the specified range, replace the S72 Sunroof Switch.
|
4. |
Test for 430-440 Ω between the signal terminal 1 and the low reference circuit terminal 4 while pressing the open switch.
|
5. |
If not within the specified range, replace the S72 Sunroof Switch.
|
6. |
Test for 96-100 Ω between the signal terminal 1 and the low reference circuit terminal 4 while pressing the express open switch.
|
7. |
If not within the specified range, replace the S72 Sunroof Switch.
|
8. |
Test for 1.7-1.8 kΩ between the signal terminal 1 and the low reference circuit terminal 4 while pressing the close switch.
|
9. |
If not within the specified range, replace the S72 Sunroof Switch.
|
10. |
Test for 930-940 Ω between the signal terminal 1 and the low reference circuit terminal 4 while pressing the express close switch.
|
11. |
If not within the specified range, replace the S72 Sunroof Switch.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Sunroof Switch Replacement
|
• |
Sunroof Module Assembly Replacement
|
• |
Control Module References
for sunroof motor/actuator replacement, setup and programming
|