SAAB WIS ONLINE

Test readings, control module connections(MIU 2)

Test readings, control module connections (MIU 2)


On the following pages you will find figures and instructions for taking readings of voltage levels on the main instrument display panel and its control module.

Remember:


Readings should be taken via a BreakOut Box (BOB) connected between the control module and its connector.

Several voltage levels should be regarded as guiding values. Use your common sense when judging whether a particular reading is correct or not.

If any reading is not OK, consult the wiring diagram to trace the leads, connectors or components which ought to be checked more thoroughly.

Pages referred to in the table contain a technical description of the signal in question.

All test readings should be taken with the engine warmed up to normal operating temperature.

Unless otherwise specified, the ignition should be switched on.

Specified test readings are in respect of calibrated FLUKE 88/97.



Pin

Component/function

Test conditions

Input/Output

Test reading

Across

See

1

Handbrake warning lamp

Handbrake off Handbrake on

Input

0 V 12 V

55-1



2

SRS warning lamp (central warning lamp)

Lamp out SRS OK

Input

about 1 V

55-2



3

SI-BUS -



Input/Output

2.5 V

3-43



4

SI-BUS +



Input/Output

2.5 V

4-43



5

Speed signal

Spin LH rear wheel 1/2 rev per sec.

Input

about 15 Hz

5-43



6

Rpm signal

Idling

Input

about 30 Hz (4-cyl.) about 40 Hz (6- cyl.)

6-43



7

Coolant temperature, signal



Input

122 Hz

7-43



8

Fuel contents, signal

Idling

Input

about 7 Hz

8-43



9

Turbo pressure signal

Ignition on

Input

about 1 V

9-10



10

Turbo pressure, ground

Idling

Input

12 V

55-10



11

Fuel level signal



Input

about 0-5 V

11-43



12

Fuel level, ground signal



Input

12 V

55-12



13

Indicator lamp EXH

On Off



12 V 0 V

13-43



14

No connection











15

Charging indicator lamp

Ignition on Engine running

Input

12 V 0 V

55-15



16

Warning lamp ABS (ANTI- LOCK)

On Off

Input

12 V 0 V

55-16



17

Warning lamp Oil pressure

On Off

Input

12 V 0 V

55-17



18

Warning lamp Brake fluid

Engine running Low Normal

Input

12 V 0 V

55-18



19

SRS 1+

Ignition on

Input

12 V

19-43



20

TCS OFF warning lamp

On Off

Input

12 V 0 V

55-20





Pin

Component/function

Test conditions

Input/Output

Test reading

Across

See

21

Repeater lamp direction indicators, RH

On Off

Input

12 V 0 V

21-43



22

Warning lamp CHECK ENGINE

On Off

Input

12 V 0 V

55-22



23

SPORT mode indicator lamp

On Off

Input

12 V 0 V

55-23



24

Reserved











25

Reserved











26

Warning lamp, SRS 1

On Off

Input

12 V 0 V

55-26



27

CHECK ACS warning lamp

On Off

Input

12 V 0 V

55-27



28

CHECK GEARBOX warning lamp

On Off

Input

12 V 0 V

55-28



29

No connection











30

No connection











31

No connection











32

No connection











33

No connection











34

No connection











35

No connection











36

No connection











37

Main beam indicator lamp

On Off

Input

12 V 0 V

37-43



38

Warning lamp Door open

On Off

Input

12 V 0 V

55-38



39

Indicator lamp SHIFT UP

On Off

Input

12 V 0 V

55-39



40

Reserved













Pin

Component/function

Test conditions

Input/Output

Test reading

Across

See

41

TCS indicator lamp

On Off

Input

12 V 0 V

55-41



42

WINTER mode indicator lamp

On Off

Input

12 V 0 V

55-42



43

Signal ground

Ignition on

Input

< 0.1 V

43-B-



44

No connection











45

No connection











46

No connection











47

No connection











48

No connection











49

No connection











50

Indicator lamp, Cruise Control CRUISE

On Off

Input

12 V 0 V

50-43



51

Repeater lamp, direction indicators

On Off

Input

12 V 0 V

51-43



52

Indicator lamp Rear fog light

On Off

Input

12 V 0 V

52-43



53

Lights indicator lamp

On Off

Input

12 V 0 V

53-43



54

Reserved







54-43



55

+ 15

Ignition on

Input

< 0.5 V

B+ -55



56

+ 30

Ignition on

Input

< 0.5 V

B+ -56