SAAB WIS ONLINE

New method, replacement of window andwindow lift, front door

SERVICE INFORMATION
Bulletin Nbr: 831-1646
Date: ........... FEBRUARI 1996
Market: ALL
New method, replacement of window and window lift, front door

Cars concerned

All Saab 900 M94-

Background

A new method of removing the scissor-lift stays has been developed.

Materials

30 25 368 Gleitmo 815

To remove, Window


1. Lower the window.

2. Remove the door trim. See Service Manual 8:2 "Interior equipment" .


3. Remove the external window seal, secured with clips at the rear.

4. Remove the plastic water barrier.

5. Remove the internal window seal by prying up the rear edge of the seal with a large screwdriver and then pulling it all the way up by hand.


6. Loosen the bottom of the rear guide channel (hanging from the window seal).

7. Raise the window until the window retainer is accessible through the lower opening on the inside of the door.

8. Remove the scissor-lift stays by removing the clips and then prying the stays away from the slide rollers with a large screwdriver. Insert the screwdriver at the top between stay and channel. Prise away near the ball to avoid deformation of the channel.


9. Lift out the glass by angling the rear edge upwards.


To fit, Window


1. Check that the scissor-lift slide rollers are undamaged and transfer them to the new glass. Fit the clips.


2. Lift the glass into place by angling it forwards and then fitting it into the front guide channel. Angle the glass rearwards and then fit it into the rear guide channel.

3. Lubricate slide rollers and sliding surfaces with grease (Gleitmo 815). Press the scissor-lift stays into position in the window retainer's slide rollers. A double click should be heard.


4. Tighten the rear guide channel.

5. Check the position of the glass in the frame and adjust the scissor-lift guide channel as follows:

Slacken the adjusting nut (the rearmost of the two guide channel retaining nuts) and raise the window all the way up in the frame.

Lower the window to about 3 cm from the closed position.

Press the glass rearwards in the frame by hand.

Check that the top edge of the glass is parallel with the frame.

Tighten the adjusting nut.

6. Fit the internal window seal by pressing it into position by hand.

7. Fit the external window seal.


Note

A rubber mallet may be needed for this.


8. Fit the plastic water barrier.

9. Fit the door trim. See Service Manual 8:2 "Interior equipment" .


To remove, window lift, front door


1. Remove the door trim. See Service Manual 8:2 "Interior equipment" .

2. Remove the plastic water barrier.

3. Lower the window about 10 cm until the window retainer is visible in the upper door holes.

4. Secure the glass in the frame using 2 strips of tape.

5. Remove the scissor-lift stays from the window retainer by removing the clips and then prying the stays away from the slide rollers with a large screwdriver. Insert the screwdriver at the top between stay and channel. Prise away near the edge to avoid deformation of the channel.


6. Run the window lift motor so that the scissor-lift occupies as little space as possible.

7. Drive in the steel cores of the pop rivets as necessary. Drill out the heads of the 4 pop rivets and then drive them out of the door panel (8.5 mm drill bit 4 mm drift).


8. Unplug the connector from the window lift motor.

9. Unscrew the scissor-lift guide channel, secured with 2 nuts.


10. Lift out the window lift.

Note

If the window lift motor is unserviceable you can tape the glass to the frame, drill out the rivets and then lower the glass.


11. Use a vacuum cleaner to remove drillings, swarf and old rivets from the doors.


To fit

Fit in reverse order.


Check that the slide rollers are undamaged.

Fit the clips on the slide rollers.

Lubricate all sliding surfaces and slide rollers with grease (Gleitmo 815) before assembly.

Fit the window lifts.

A double click should be heard when the scissor-lift stays are pressed into position in the window retainer's slide rollers.

Note

This work will be facilitated if a heavy-duty pop rivet tool is used. Adjust the position of the glass as follows:

Raise the window to 3 cm from the closed position.

Press the glass rearwards in the frame.

Check that the top edge of the glass is parallel with the frame.



Standard time information

Object code: 84321 Change door window

83510 Change window lift

Localization code: 03/04

Action code: 02

Time: 0.4 Change door window LH/RH

0.4 Change window lift LH/RH

Warranty information

Standard warranty rules apply.