SAAB WIS ONLINE

B2332, B2337

B2332, B2337

Airbag, driver, short circuit to ground / Airbag, passenger, short circuit to ground

The reference resistor is available in two versions. A newer, part no. 86 12 095 , and an older, part no. 84 71 153 . The new type has closer tolerance limits and should be used for more reliable diagnosis. The illustrations in the following chapter show the older type of reference resistor.


















Diagnostic procedure


1. Connect the diagnostic tool. Note the diagnostic trouble code and type of fault.


P=permanent fault, I=intermittent fault.

If the fault is permanent:

Go to point 3.

If the fault is intermittent:

Go to point 2.

2. The fault is intermittent. Try to provoke the fault at each test section in the continued fault diagnosis.

Move the connectors and cables and turn the steering wheel while testing.

Important

If no fault can be shown while testing, the contact roller should be changed. The contact roller is the most common cause for intermittent faults.


Go to point 3.

3. Turn off the ignition and remove the negative cable from the battery. Undo the bolts securing the steering wheel airbag. Unplug the connector from the back of the airbag and connect the reference resistor 84 71 153 to the connector.

On cars with airbag on passenger side;

3.a. Remove the glove-box and unplug the connector on the back of the passenger airbag.

3.b. Connect the reference resistor 84 71 153 to the connector.

Go to point 4.

4. Refit the negative cable to the battery and turn on the ignition. Clear the fault codes. Turn off the ignition and turn it on again, wait for at least 10 seconds with the ignition on.


Check to see if the diagnostic trouble code returns.

If the diagnostic trouble code returns:

Go to point 7.

If the diagnostic trouble code does not return:

The fault is in the driver or passenger airbag (if fitted). Perform an extra check as described in point 5.

5. Turn off the ignition and remove the negative cable on the battery. Remove the reference resistor from the airbag connector and connect the airbag.


Refit the negative cable on the battery and turn on the ignition. Wait for at least 10 seconds with the ignition on.

Check to see if the diagnostic trouble code returns.

If the diagnostic trouble code returns:

Turn off the ignition and remove the negative cable on the battery. Change the steering wheel airbag. Then go to point 11.

If the diagnostic trouble code does not return:

If the car is equipped with airbag on the passenger side, turn off the ignition and remove the negative battery cable. Unplug the connector from the steering wheel airbag. Reconnect the negative battery cable and then go to point 7.

6. Turn off the ignition and remove the negative battery cable. Reconnect the reference resistor to the airbag connector on the driver's side.


Remove the reference resistor from the passenger airbag connector and connect the passenger airbag.

Refit the negative cable on the battery and turn on the ignition. Wait for at least 10 seconds with the ignition on.

Check to see if the diagnostic trouble code returns.

If the diagnostic trouble code returns:

Turn off the ignition, remove the negative battery cable and change the airbag on the passenger side. Then go to point 11.

If the diagnostic trouble code does not return:

Turn off the ignition and remove the negative battery cable. Unplug the connector from the passenger airbag and reconnect the reference resistor. Reconnect the negative battery cable and then go to point 7.

7. Turn off the ignition and remove the reference resistor from the airbag connector on the driver's side.


Remove the connector from the SRS control module and connect a BOB to the wiring harness.

Connect an ohmmeter between connector 10 on BOB and a good grounding point. Then connect an ohmmeter between connection 11 on BOB and a good grounding point. In both cases, the ohmmeter should read infinite resistance.

If the value is OK:

If the car is equipped with an airbag on the passenger side, go to point 10.

If the car is not fitted with an airbag on the passenger side, go to point 11.

If the value differs:

Go to point 8.

8. Turn off the ignition and unplug connector H2-52.


Connect an ohmmeter between connection 10 on BOB and a good grounding point. Then connect an ohmmeter between connection 11 on BOB and a good grounding point.

The ohmmeter should indicate infinite resistance.

If the value is OK:

Go to point 9.

If the value differs:

If any of the readings indicates low resistance, there is a short circuit to ground in the corresponding lead between SRS connector and connector H2-52. Locate the cause and change the wiring harness. Then go to point 11.

9. Connect an ohmmeter between pin 1 in connector H2-52 from the contact roller and a good grounding point. Then connect an ohmmeter between pin 3 in the connector and a good grounding point.


The ohmmeter should indicate infinite resistance.

If the value is OK:

If the car is equipped with an airbag on the passenger side, go to point 10.

If the car is not fitted with an airbag on the passenger side, go to point 11.

If the value differs:

If any of the readings indicates low resistance, the fault is in the contact roller. Change the contact roller and then go to point 11.

10. Turn off the ignition and remove the reference resistor from the passenger airbag connector.


Connect an ohmmeter between connection 13 on BOB and a good grounding point. Then connect an ohmmeter between connection 14 on BOB and a good grounding point.

In both cases, the ohmmeter should indicate infinite resistance.

If the value is OK:

Go to point 11.

If the value differs:

If any of the readings indicates low resistance, there is an overload to ground on the corresponding lead. Locate the cause and change the wiring harness. Go to point 11.


11. Turn off the ignition and remove the negative cable on the battery. Remove the reference resistor and plug in all the connectors to their original components. Reconnect the negative cable on the battery and turn on the ignition.


Clear the diagnostic trouble codes. Turn off the ignition and turn it on again, wait for at least 10 seconds with the ignition on. Check to see if the diagnostic trouble codes return.

If the diagnostic trouble code returns:

Go to section: Procedure for replacing the control module .

If the diagnostic trouble code does not return:

Restore the car.