|
Parameter
|
System State
|
Expected Value
|
Description
|
Base Operating Conditions: Engine Idling/Radiator Hose Hot/Park or Neutral/Closed Loop
|
5 V Reference 1,2,3 or 4
|
Ignition ON
|
Volts
|
This parameter displays the voltage sensed on the 5-volt reference circuit at the control module. The scan tool will display a higher value at higher voltage. The scan tool will display a lower value at lower voltage.
|
5 V Reference 1, 2, 3 or 4 Circuit Status
|
Ignition ON
|
OK / Malfunction
|
This parameter will display OK if the circuit is good or Malfunction if a short to ground, short to B+ or open circuit is present.
|
A/C Compressor Operation
|
A/C ON
|
Allowed / Not Allowed
|
This parameter displays if the A/C compressor is allowed or not allowed to operate.
|
A/C Disengage 1-8 History
|
A/C ON
|
Reason for A/C Disengagement
|
The parameter displays reason for the last 8 air conditioning (A/C) compressor disengagements in order from 1 to 8 with 8 being the most recent. There are 8 possible causes for the A/C compressor to disengage.
|
A/C High Side Pressure Sensor
|
A/C OFF
|
0.75-1.5 V*
|
This parameter displays the voltage signal from the A/C high side pressure sensor input to the control module.
* Varies with temperature, humidity, and altitude.
|
A/C ON
|
1.3-2.5 V*
|
A/C High Side Pressure Sensor
|
A/C OFF
|
450-827 kPa (65-120 psi)*
|
This parameter displays the pressure from the A/C high side pressure sensor signal circuit to the control module.
* Varies with temperature, humidity, and altitude.
|
A/C ON
|
827-2,350 kPa (120-341 psi)*
|
A/C OFF for WOT
|
A/C ON
|
Yes / No
|
This parameter displays whether the control module is commanding the A/C compressor clutch relay OFF for wide open throttle (WOT).
|
A/C Pressure Out of Range
|
A/C ON
|
Yes / No
|
This parameter displays whether the A/C pressure is out of range for normal operation as determined by the control module.
|
A/C Request Signal
|
A/C ON
|
Yes / No
|
This parameter displays the state of the A/C request input to the control module from the heating, ventilation, and air conditioning (HVAC) controls.
|
Accelerator Pedal Position
|
Ignition ON
|
%
|
This parameter displays the angle of the accelerator pedal position (APP) as calculated by the control module using the signals from the APP sensors.
|
Actual Fuel Rail Pressure (If Equipped)
|
Engine Idling
|
3.4-5.5 MPa (500-800 psi)
|
This parameter displays the Actual Fuel Rail Pressure in a range from 0-2900 psi.
|
Air/Fuel Equivalence Ratio Command
|
Engine Idling
|
:1
|
This parameter should display 1.0 when in Closed Loop fuel control.
|
Ambient Air Temperature
|
Engine Idling
|
°C °F Varies
|
This parameter displays the outside air temperature as calculated by the control module.
|
Ambient Air Temperature When Recommended Maximum Fuel Alcohol Content Exceeded
|
Engine Idling
|
°C °F Varies
|
This parameter displays the estimated ambient air temperature at the most recent time that the Recommended Ethanol Concentration Exceeded became true.
|
APP Sensor
|
Ignition ON
|
%
|
This Parameter contains the accelerator pedal position resulting directly from the settling of differences of the accelerator pedal position sensors (prior to any compensation to determine driver intent).
|
APP Sensor 1 Circuit Status
|
Ignition ON
|
OK / Malfunction
|
APP Sensor 1 Out of Range indicates that the sensed accelerator pedal position 1 sensor value is currently out of range or that a Malfunction has been detected based upon the sensed accelerator pedal position 1 sensor value being out of range.
|
APP Sensor 1 Learned Applied Position
|
Ignition ON
|
%
|
This parameter contains the learned maximum (fully applied) accelerator pedal position relating to absolute accelerator pedal position (no correction or normalization based upon learned minimum or maximum positions) from accelerator pedal position sensor 1.
|
APP Sensor 1 learned Released Position
|
Ignition ON
|
V
|
This parameter indicates the signal from the accelerator pedal sensor 1 at the lowest programmed position (pedal released) as a percentage of its reference voltage. The lowest programmed position is updated automatically at regular intervals as determined by the calibration.
|
APP Sensor 1 Position
|
Ignition ON
|
%
|
This Parameter contains the displacement determined from accelerator pedal position sensor 1 (corrected and normalized based upon its learned minimum and maximum positions).
|
APP Sensor 2
|
Ignition ON
|
V
|
This Parameter contains the accelerator pedal position sensor 2 analog input as a percentage of its reference voltage.
|
APP Sensor 2 Circuit Status
|
Ignition ON
|
OK / Malfunction
|
APP Sensor 2 Out of Range indicates that the sensed accelerator pedal position 2 sensor value is currently out of range or that a malfunction has been detected (and latched) based upon the sensed accelerator pedal position 2 sensor value being out of range.
|
APP Sensor 2 Learned Applied Position
|
Ignition ON
|
%
|
This Parameter contains the learned maximum (fully applied) accelerator pedal position relating to absolute accelerator pedal position (no correction or normalization based upon learned minimum or maximum positions) from accelerator pedal position sensor 2.
|
APP Sensor 2 Learned Released Position
|
Ignition ON
|
V
|
This parameter indicates the signal from the accelerator pedal sensor 2 at the lowest programmed position (pedal released) as a percentage of its reference voltage. The lowest programmed position is updated automatically at regular intervals as determined by the algorithm.
|
APP Sensor 2 Position
|
Ignition ON
|
%
|
This parameter contains the displacement determined from accelerator pedal position sensor 2 (corrected and normalized based upon its learned minimum and maximum positions).
|
APP Sensor 1
|
Accelerator pedal not actuated
|
0.7-1.2 V
|
This parameter displays the actual voltage on the accelerator pedal position (APP) sensor 1 signal circuit as measured by the control module.
|
Accelerator pedal fully actuated
|
4.2-4.5 V
|
APP Sensor 2
|
Accelerator pedal not actuated
|
0.3-0.5 V
|
This parameter displays the actual voltage on the accelerator pedal position (APP) sensor 2 signal circuit as measured by the control module.
|
Accelerator pedal fully actuated
|
2.2-2.5 V
|
APP Sensor 1 and 2
|
Ignition ON
|
Agree / Disagree
|
This parameter displays Disagree if the control module detects the signal voltage from APP sensor 1 is not in correct relationship to APP sensor 2. The scan tool displays Agree under the normal operating conditions.
|
BARO
|
Engine Idling
|
65-104 kPa (8-16 psi)
|
This parameter displays the barometric pressure. The control module uses the barometric pressure sensor input for fuel control to compensate for altitude differences.
|
BARO Sensor
|
Engine Idling
|
Volts
|
This parameter displays the barometric pressure sensor voltage.
|
Boost Pressure
|
Engine Idling
|
kPa
|
This parameter shows the Turbocharger boost pressure in kPa.
|
Boost Pressure Sensor
|
Engine Idling
|
Volts
|
This parameter shows the Turbo Charger Boost sensor voltage.
|
Boost Pressure Sensor
|
Engine Idling
|
kPa
|
This parameter shows the Turbocharger boost pressure in kPa.
|
Brake Pedal Position Circuit Signal
|
Ignition ON
|
Applied / Released
|
This parameter displays the serial data message of the brake signal from the electronic brake and traction control module (EBTCM).
|
Brake Pedal Position Sensor Signal
|
Ignition ON
|
Applied / Released / Invalid
|
This parameter displays the serial data message of the brake position sensor signal from the electronic brake and traction control module (EBTCM).
|
Calculated Air Flow
|
Engine Idling
|
g/s
|
This Parameter contains the mass airflow determined from the speed density (MAP based) calculation of air mass per cylinder.
|
Calculated BARO (If Equipped)
|
Engine Idling
|
kPa
|
This parameter contains an estimate of barometric pressure, used to correlate with sensed ambient air pressure in the Barometric Pressure Correlation Diagnostic.
|
Calculated Catalyst Temperature
|
Engine Idling
|
°C / °F
|
This Parameter contains the estimated catalyst temperature for bank 1 sensor 1 (as a function of engine speed, engine airflow, and fuel ethanol percentage) for use in the oxygen sensor and catalyst monitor diagnostic algorithms.
|
Calculated Engine Oil Temperature
|
Engine Idling
|
Degrees
|
This Parameter contains the estimated engine oil temperature (as a function of engine coolant temperature and other parameters).
|
Camshaft Position Sensor
|
Engine Idling
|
RPM
|
This parameter contains the engine speed determined from the period of the primary cam position sensor.
|
Catalyst Monitor Complete
|
Engine Idling
|
Yes/No
|
This parameter displays the completion status during the current driving/monitoring cycle of the non-continuous legislated emission related monitor. The states include Yes or No.
|
Catalyst Monitor Complete This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This parameter indicates the status of the catalyst monitor diagnostic. Catalyst Monitor Test Running indicates yes or no when the catalyst monitor diagnostic is actively running a test.
|
Catalyst Monitor Enabled
|
Engine Idling
|
Yes / No
|
This parameter displays the enable status during the current driving/monitoring cycle of the non-continuous legislated emission related monitor. The states include Yes or No.
|
Catalyst Monitor Enabled This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This parameter indicates the status of the catalyst monitor diagnostic. Catalyst Monitor Test Running indicates yes or no when the catalyst monitor diagnostic is actively running a test.
|
Catalyst Monitor Not At Idle Test Conditions Met
|
Engine Idling
|
Yes / No
|
This parameter indicates the status of the catalyst monitor diagnostic. Catalyst Monitor Test Running indicates yes or no when the catalyst monitor diagnostic is actively running a test.
|
Catalyst Monitor Test Counter
|
Engine Idling
|
Quantity
|
This Parameter contains the number of repeated results of the catalyst monitor diagnostic test that have been performed since a code clear for bank 1 (used to determine if a sufficient number of tests have run to report a passing condition).
|
Catalyst Monitor Test Result
|
Engine Idling
|
No Result / Failed / Passed
|
This Parameter indicates the status of the catalyst monitor diagnostic for bank1. Multiple tests may be run before the diagnostic reports a "Pass" or "Fail" and will be tracked by Catalyst monitor diagnostic test counter, bank 1. When this parameter reports a Pass or Fail, the diagnostic is complete for the current trip and will not attempt any further tests on bank 1.
|
Catalyst Monitor Test State
|
Engine Idling
|
Active / Inactive
|
This Parameter indicates the status of the catalyst monitor diagnostic by displaying active or inactive. This test will only run with the engine at idle.
|
Catalyst Monitor Enabled This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This parameter displays the monitor enable status during the current driving/monitoring cycle.
|
Change Engine Oil Indicator Command
|
Ignition ON
|
ON / OFF
|
This Parameter sends a signal through the serial communication to inform the driver to change the engine oil. It is based on a calibrated amount of time.
|
Crankshaft Position Active Counter
|
Engine Idling
|
0-255 Counts
|
This parameter displays an incrementing counter when the control module receives a signal from the crankshaft position sensor.
|
Crankshaft Position Resync Counter
|
Engine Idling
|
0 Counts
|
This parameter displays the number of times the control module has to resynchronize with the crankshaft position sensor. The parameter will begin to increment if the control module does not detect a crankshaft position reference pulse. The parameter will reset to 0 after the ignition is switched OFF.
|
Camshaft Position Sensor
|
Engine Idling
|
0 RPM
|
This parameter displays the speed of the engine as calculated by the signal from a camshaft position sensor. This parameter will always display 0 unless a condition with the crankshaft position sensor or crankshaft position reluctor exists. If a crankshaft position condition exists the control module will use a valid camshaft position sensor signal to determine engine speed and crank/camshaft position.
|
Cold Startup
|
Ignition ON
|
Yes / No
|
This parameter displays whether the engine meets the conditions for a cold startup during the present ignition cycle. The scan tool displays Yes when the conditions for a cold startup are met during the ignition cycle. The scan tool displays No when the conditions for a cold startup are not met during the present ignition cycle. Conditions for a cold startup require the coolant temperature and the intake air temperature to be below a predetermined temperature and within a certain range of each other. These conditions must occur after the engine was warmed up to a specific temperature during the previous ignition cycle.
|
Cooling Fan Relay 1 Command
|
Ignition ON
|
ON / OFF
|
This parameter indicates the command status for the control circuit for fan relay 1. The cooling fan relay 1 should be ON when the diagnostic tool indicates that the FC relay 1 command is ON. The cooling fan relay should be OFF when the diagnostic tool indicates that the FC relay 1 command is OFF.
|
Cooling Fan Relay 1 Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the fan relay control circuit. The parameter displays Malfunction if the fan relay control circuit is shorted to voltage.
|
Cooling Fan Relay 1 Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction/Not Run
|
This parameter displays the state of the fan relay control circuit. The parameter displays Malfunction if the fan relay control circuit is shorted to ground.
|
Cooling Fan Relay 1 Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the fan relay control circuit. The parameter displays Malfunction if the fan relay control circuit is open.
|
Cooling Fan Relay 2 Command (If equipped)
|
Ignition ON
|
ON / OFF
|
This parameter indicates the command status for the control circuit for fan relay 2. The cooling fan relay 2 should be ON when the diagnostic tool indicates that the FC relay 2 command is ON. The cooling fan relay should be OFF when the diagnostic tool indicates that the FC relay 2 command is OFF.
|
Cooling Fan Relay 2 Control Circuit High Voltage Test Status (If equipped)
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the fan relay control circuit. The parameter displays Malfunction if the fan relay control circuit is shorted to voltage.
|
Cooling Fan Relay 2 Control Circuit Low Voltage Test Status (If equipped)
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the fan relay control circuit. The parameter displays Malfunction if the fan relay control circuit is shorted to ground.
|
Cooling Fan Relay 2 Control Circuit Open Test Status (If equipped)
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the fan relay control circuit. The parameter displays Malfunction if the fan relay control circuit is open.
|
Cooling Fan Speed
|
Ignition ON
|
Varies
|
This Parameter displays the current state of the cooling fan speed. For example OFF, Low, Medium, or High rather than rotational speed.
|
Crankshaft Position Sensor
|
Engine Idling
|
RPM
|
This Parameter displays engine speed.
|
Crank Request Signal
|
Ignition switch not in the crank position
|
No
|
This parameter displays whether the ignition switch has been cycled to the crank position requesting the control module to activate the starter relay.
|
Ignition switch in the crank position
|
Yes
|
Cruise Control
|
Cruise ON
|
Active / Inactive
|
This parameter displays the status of the cruise control system as determined by the control module.
|
Cruise Control Cancel Switch
|
Cruise ON
|
Active
|
This parameter displays the status of the cruise control cancel switch as determined by the control module. The scan tool will display active when the cruise control cancel switch is on. The scan tool will display inactive when the cruise control cancel switch is off.
|
Cruise Control Disengage 1-8 History
|
Cruise ON
|
Reason for Cruise Disengagement
|
The parameter displays the last 8 cruise control disengages in order from 1 to 8, with 8 being the most recent. There are approximately 30 possible causes for the cruise control to disengage.
|
Cruise Control Inhibit Reason
|
Cruise OFF
|
Off
|
The parameter displays the reason the cruise control system cannot engage.
|
Cruise ON
|
Park / Neutral
|
Cruise Control ON/OFF Switch
|
Cruise ON
|
ON / OFF
|
The engine control module (ECM) monitors the signal circuit of the cruise control switch. A closed switch is displayed as ON.
|
Cruise Control Resume/Accel. Switch
|
Cruise ON
|
Active / Inactive / Invalid
|
The scan tool displays ON, when the cruise ON/OFF switch is ON and the resume/accel (+) button is pressed, the ECM detects a predetermined voltage value for the resume/accel. switch.
|
Cruise Control Set/Coast Switch
|
Cruise ON
|
Active / Inactive / Invalid
|
The scan tool displays ON, when the cruise ON/OFF switch is ON and the ECM detects a predetermined voltage value for the set/coast (-) switch.
|
Current Gear
|
Transmission in Park/Neutral
|
P/N
|
This parameter displays the transmission gear commanded by the transmission control module.
|
Transmission not in Park/Neutral
|
Reverse / 1st-5th
|
Cycles of Misfire Data
|
Engine Idling
|
0-3,000 counts
|
This parameter displays the number of cylinder firing events recorded by the control module.
|
Cylinder 1-4 Current Misfire Counter
|
Engine running
|
Quantity
|
The scan tool displays a range of 0--255 counts. This parameter displays the number of misfires that have been detected during the last 255 cylinder firing events. The counters may normally display some activity, but the activity should be nearly equal for all of the cylinders, and in low numbers.
|
Cylinder 1-4 History Misfire Counter
|
Engine Idling
|
Quantity
|
The scan tool displays a range of 0-65,535 counts. The misfire history counters display the total level of misfire that has been detected on each cylinder. The misfire history counters will not update or show any activity until a misfire DTC P0300 has become active. The misfire history counters will update every 255 cylinder firing events.
|
Cylinder 1-4 Injector Control Circuit Status
|
Engine Idling
|
OK
|
This parameter displays the state of the Fuel Injector Control Circuit.
|
Cylinder 1-4 Injector Control Circuit Status
|
Ignition ON
|
OK / Not Run
|
This parameter displays the state of the Fuel Injector Control Circuit.
|
Cylinder 1-4 Injector Disabled Misfire Detected
|
Engine Idling
|
Yes / No
|
This parameter displays the injector that has been disabled by the misfire catalyst converter protection calibration.
|
Cylinder 1-4 Knock Detected
|
Engine Idling
|
Yes / No
|
This parameter displays yes if a knock has been detected in an individual cylinder.
|
Deceleration Fuel Cutoff
|
Engine Idling
|
Active / Inactive
|
This parameter displays the status of the operating mode of the control module used to turn OFF the fuel injectors and the EVAP canister purge valve during certain deceleration conditions.
|
Desired Boost Pressure
|
Engine Idling
|
kPa
|
This parameter displays the desired turbocharger boost pressure as determined by the engine control module.
|
Desired Exhaust Camshaft Position (If Equipped)
|
Engine Idling
|
0 Degrees
|
This parameter displays the desired exhaust camshaft angle as commanded by the control module.
|
Engine speed at 2000 RPM
|
10 Degrees
|
Desired Fuel Rail Pressure (If Equipped)
|
Engine Idling
|
Varies
3.4-5.5 MPa (500-800 psi)
|
This parameter displays the desired Fuel Rail Pressure commanded by the control module.
|
Desired Idle Speed
|
Engine Idling
|
Approximately 650 RPM
|
This parameter displays the desired engine idle speed as commanded by the control module. The desired idle speed varies depending on engine load.
|
Desired Intake Camshaft Position
|
Engine Idling
|
0 Degrees
|
This parameter displays the desired intake camshaft angle as commanded by the control module.
|
Engine speed at 2000 RPM
|
10 Degrees
|
Desired Throttle Position
|
Ignition ON
|
%
|
Commanded Throttle Actuator Control
|
Distance Since DTC Cleared
|
Ignition ON
|
0 Km/mi
|
This parameter displays in kilometers or miles the distance traveled since a DTC was cleared.
|
Distance Since First Malfunction
|
Ignition ON
|
0 Km/mi
|
This parameter displays in kilometers or miles the distance traveled since a Malfunction occurred.
|
Distance Since Recommended Maximum Fuel Alcohol Content Exceeded
|
Ignition ON
|
0 Km/mi
|
This parameter displays in kilometers or miles the distance driven since the most recent time that the Recommended Ethanol Concentration Exceeded occurred.
|
Drag Control Status
|
Vehicle Moving
|
Active / Inactive
|
EDC Active (Drag Active) control mode is indicated when the requested torque signal is above the driver requested value while the traction control system signal input is active.
|
ECM Authentication Status
|
Ignition ON
|
Unknown / Incorrect / Negative Response / Valid
|
ECM Authentication Status indicates the result of the comparison between the last received immobilizer response and the expected response calculated into the ECM.
|
ECM Response Source
|
Ignition ON
|
Ignition Switch Start / Remote Vehicle Start / Exterior PTO Vehicle Start
|
ECM Response Source indicates the source used to calculate the ECM response.
|
ECM Challenge Status
|
Ignition ON
|
Valid
|
This parameter displays the ECM challenge as Valid or Invalid.
|
ECT Sensor
|
Ignition ON
|
88-105°C (190-221°F)
|
This parameter displays the temperature of the engine coolant based on input to the control module from the engine coolant temperature (ECT) sensor.
|
EGR/Camshaft Position Monitor Complete This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This Parameter displays Yes or No of the completion status during the current driving / monitoring cycle of emission related monitors.
|
EGR/Camshaft Position Monitor Enabled This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This Parameter displays Yes or No of the completion status during the current driving / monitoring cycle of emission related monitors.
|
Electric Power Management Inhibit Reason
|
Engine Idling
|
None / Control Function / Active / Fuel System / On-board Diagnostic System / Air Flow Measurement System / Cylinder Deactivation System / System Transmission Control Module
|
This Parameter displays the reason for the source of the Regulated Voltage Control (RVC) override command. RVC lowers system operating voltage to reduce system electrical load and improve fuel economy performance.
|
Engine Controls Ignition Relay Command
|
Ignition ON
|
ON / OFF
|
This parameter displays the state of the control circuit for control module power relay as commanded by the control module.
|
Engine Controls Ignition Relay Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the Engine Controls Ignition Relay control circuit. The parameter displays Malfunction if the Engine Control's Ignition Relay control circuit is shorted to voltage.
|
Engine Controls Ignition Relay Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the Engine Controls Ignition Relay control circuit. The parameter displays Malfunction if the Engine Control's Ignition Relay control circuit is shorted to ground.
|
Engine Controls Ignition Relay Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the Engine Controls Ignition Relay control circuit. The parameter displays Malfunction if the Engine Control's Ignition Relay control circuit is open.
|
Engine management system's ignition relay feedback signal
|
Ignition ON
|
12.0-14.9 V
|
This parameter displays the voltage available at the EC ignition relay pin of the control module.
|
Engine Load
|
Engine Idling
|
25-45 %
|
This parameter displays the calculated engine load in percent based on inputs to the control module from various engine sensors.
|
Engine speed at 2,500 RPM
|
40-60 %
|
Engine OFF Time
|
Engine OFF
|
0:00:00 Seconds / Varies
|
This parameter displays the amount of time that has elapsed since the engine was last cycled OFF.
|
Engine Oil Level Switch (If Equipped)
|
Ignition ON
|
OK
|
This parameter displays if the level of the engine oil is within range as determined by the control module from information received from the engine oil level switch.
|
Engine Oil Life Remaining.
|
Ignition ON
|
0-100 %
|
This parameter displays the percent of engine oil life remaining. The controller calculates the engine oil life by monitoring engine load, coolant temperature, and engine speed.
|
Engine Oil Pressure Sensor (If Equipped)
|
Engine running
|
103-241 kPa (15-35 psi)
|
This parameter displays the engine oil pressure.
|
Engine run time
|
Engine Operating
|
0:00:00
Increments when the engine is operating
|
This parameter displays the time elapsed since the engine was started.
|
Engine Speed
|
Engine cranking
|
Greater than 60 RPM
|
This parameter displays the speed of the engine crankshaft rotation from information received from the crankshaft position sensor. If there is a crankshaft position sensor DTC, the ECM calculates the engine speed from one of the camshaft position sensors.
|
Engine Idling
|
550-700 RPM
|
EVAP Malfunction History
|
Engine running
|
No Fault
|
This parameter displays the result of the evaporative emission (EVAP) system as determined by the control module. The scan tool will display the following:
|
EVAP Monitor Complete This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This parameter displays the diagnostic monitor completion status during the current driving/monitoring cycle.
|
EVAP Monitor Enabled This Ignition Cycle
|
Engine running
|
Yes / No
|
This parameter displays the diagnostic monitor enable status during the current driving/monitoring cycle.
|
EVAP Purge Solenoid Valve Command
|
Engine Idling
|
%
|
This Parameter displays the commanded duty cycle for the canister purge output.
|
EVAP Purge Solenoid Valve Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the evaporative emission (EVAP) purge solenoid control circuit. The parameter displays Malfunction if the EVAP purge solenoid control circuit is shorted to ground.
|
EVAP Purge Solenoid Valve Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the evaporative emission (EVAP) purge solenoid control circuit. The parameter displays Malfunction if the EVAP purge solenoid control circuit is open.
|
EVAP Purge Solenoid Valve Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the evaporative emission (EVAP) purge solenoid control circuit. The parameter displays Malfunction if the EVAP purge solenoid control circuit is shorted to voltage.
|
EVAP Purge Solenoid Valve Command
|
Ignition ON
|
0-100 %
|
This parameter displays the on-time or duty cycle of the EVAP canister purge solenoid commanded by the control module. Zero percent indicates no purge. One hundred percent indicates full purge.
|
EVAP Vent Solenoid Command
|
Engine Idling
|
Venting / Not Venting
|
This parameter displays the state of the control circuit for evaporative emission (EVAP) vent solenoid as commanded by the control module.
|
EVAP Vent Solenoid Valve Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter shows the status of the control circuit for the EVAP ventilation solenoid. The parameter indicates a fault if the control circuit is shorted to ground. This parameter may not change if the scan tool is used to command the EVAP vent solenoid ON.
|
EVAP Vent Solenoid Valve Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter shows the status of the control circuit for the EVAP ventilation solenoid. The parameter indicates a fault if the control circuit is open circuit. This parameter may not change if the scan tool is used to command the EVAP vent solenoid ON.
|
EVAP Vent Solenoid Valve Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter shows the status of the control circuit for the EVAP ventilation solenoid. The parameter indicates a fault if the control circuit is shorted to voltage. This parameter may not change if the scan tool is used to command the EVAP vent solenoid ON.
|
Exhaust Camshaft Position
|
Engine Idling
|
0 Degrees
|
This parameter displays the actual exhaust camshaft position in degrees.
|
Engine speed at 2000 RPM
|
10 Degrees
|
Exhaust Camshaft Position Active Counter
|
Engine Idling
|
0-255
|
This parameter displays an incrementing counter when the control module receives a signal from the exhaust camshaft position sensor.
|
Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the exhaust camshaft actuator solenoid control circuit. The parameter displays Malfunction if the camshaft actuator solenoid control circuit is shorted to ground.
|
Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the exhaust camshaft actuator solenoid control circuit. The parameter displays Malfunction if the camshaft actuator solenoid control circuit is open.
|
Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the exhaust camshaft actuator solenoid control circuit. The parameter displays Malfunction if the camshaft actuator solenoid control circuit is shorted to voltage.
|
Exhaust Camshaft Position Command
|
Engine Idling
|
20 %
|
This parameter displays the on-time or duty cycle of the exhaust camshaft position actuator solenoid valve as commanded by the control module.
|
Engine speed at 2000 RPM
|
50 %
|
Exhaust Camshaft Position Variance
|
Engine Idling
|
0 Degrees
|
This parameter displays in degrees, the difference between the desired exhaust camshaft position and the actual exhaust camshaft position.
|
Engine speed at 2000 RPM
|
0 Degrees
|
Extended Travel Brake Pedal Position Signal
|
Ignition ON
|
Applied / Released / Invalid
|
This parameter will display the state of the brake pedal, applied or released.
|
Fuel Alcohol Content (If Equipped)
|
Ignition ON
|
%
|
This parameter displays the percentage of alcohol contained in ethanol fuels, if equipped.
|
Fuel Alcohol Content When Recommended Maximum Fuel Alcohol Content Exceeded, If Equipped
|
Ignition ON
|
%
|
This Parameter displays the actual fuel alcohol percentage at the most recent time that the Recommended Ethanol Concentration Exceeded became true. If a Recommended Ethanol Concentration Exceeded event has not taken place this Parameter shall default to zero.
|
Fuel Composition Sensor (If equipped)
|
Ignition ON
|
Hz
|
This Parameter displays the frequency of the fuel composition sensor input. This value can be viewed to determine fuel composition or sensor fault status, depending on the value.
|
Fuel Consumed Since Recommended Maximum Fuel Alcohol Content Exceeded (If equipped)
|
Engine Idling
|
Liter
|
This Parameter displays the amount of fuel consumed since the most recent time that the Recommended Ethanol Concentration Exceeded became true. This Parameter value can be reset when a code clear is performed to the controller. If a Recommended Ethanol Concentration Exceeded event has not taken place this Parameter shall default to zero.
|
Fuel Control Loop Status
|
Engine Idling
|
Open / Closed
|
Fuel Closed Loop Active indicates that oxygen sensor 1 of each bank is being used as feedback to adjust the amount of fuel delivered to the engine.
|
Fuel economy
|
Engine Idling
|
Varies
|
This parameter displays the instant fuel consumption rate of the engine in liters per hour.
|
Fuel Enrichment-Hot Catalyst
|
Engine running
|
Active / Inactive
|
Fuel Enrichment Catalyst Protection Active indicates fuel is being added to cool the catalytic converter.
|
Fuel Enrichment-Hot Coolant
|
Engine running
|
Active / Inactive
|
Hot Coolant Enrichment Active indicates that the conditions to enable hot coolant enrichment are active and that a richer than stoichiometric air/fuel ratio is being commanded in order to help cool the engine when a system malfunction is causing the engine to run at extreme temperatures.
|
Fuel Injector Driver Supply Voltage
|
Ignition ON
|
Varies
|
This Parameter displays the injector driver circuit boost supply voltage. The boost voltage is monitored and a value that is too high or too low will lead to report a fail of DTC P062B.
|
Fuel Level Sensor Left Tank (If Equipped)
|
Ignition ON
|
0-5 V
|
This parameter displays the voltage signal received by the control module from the secondary fuel level sensor in the left side of the fuel tank.
|
Fuel Level Sensor Right Tank (If Equipped)
|
Ignition ON
|
0-5 V
|
This parameter displays the voltage signal received by the control module from the primary fuel level sensor in the right side of the fuel tank.
|
Fuel Pressure Regulator Control Circuit Command
|
Engine Cranking or Running
|
ON / OFF
|
This Parameter displays the commanded state of the fuel pressure regulator 1 low side output (the output is considered to be commanded ON if the regulator is enabled while the engine is running or cranking).
|
Fuel Pressure Regulator Control Circuit High Voltage Test
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pressure regulator control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an short to voltage in the circuit.
|
Fuel Pressure Regulator Control Circuit Low Voltage Test
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pressure regulator control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an short to ground in the circuit.
|
Fuel Pressure Regulator Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pressure regulator control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an open in the circuit.
|
Fuel Pressure Regulator High Control Circuit Command
|
Engine Idling
|
%
|
This Parameter displays the commanded duty cycle for the fuel pressure regulator 1 solenoid output.
|
Fuel Pressure Regulator High Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pressure regulator high control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an short to voltage in the circuit.
|
Fuel Pressure Regulator High Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pressure regulator high control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an short to ground in the circuit.
|
Fuel Pressure Regulator High Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pressure regulator high control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an open in the circuit.
|
Fuel Pressure Sensor
|
Engine Idling
|
kPa/psi
|
For Port Fuel Injected (PFI) systems, this Parameter displays fuel rail pressure at the engine. For high pressure fuel systems, this Parameter indicates the low side fuel pressure before the high pressure pump.
|
Fuel Pump Enabled Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pump control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an short to voltage in the circuit.
|
Fuel Pump Enabled Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pump control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an short to ground in the circuit.
|
Fuel Pump Enabled Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the status of the output driver for the fuel pump control circuit. The scan tool will display OK if the circuit is operating correctly or Not Run if a diagnosis has not been made. The scan tool will display Malfunction if there is an open in the circuit.
|
Fuel Pump Enable Command
|
Ignition ON
|
ON / OFF
|
This Parameter displays the commanded state of the fuel pump output (the output is considered to be commanded ON if its duty cycle is not zero).
|
Fuel Rail Pressure Regulator Command (If Equipped)
|
Engine idling
|
130-135 Degrees
|
The scan tool displays in degrees, the Fuel Rail Pressure Regulator ON time as commanded by the control module.
|
Fuel Rail Pressure Sensor (If Equipped)
|
Engine Idling
|
MPa / psi
|
This Parameter displays the high side fuel pressure after the high pressure pump.
|
Fuel Rail Pressure Sensor (If Equipped)
|
Engine Idling
|
0-5 V
|
This parameter displays the voltage signal received by the control module from the fuel rail pressure (FRP) sensor.
|
Fuel Tank Pressure
|
Ignition ON, engine OFF
|
0 in H2O / mm Hg
|
This parameter displays the pressure/vacuum inside the fuel tank. A negative value indicates a vacuum, while a positive value indicates a pressure.
|
0-5 V
|
This parameter displays the voltage signal received by the control module from the fuel tank pressure (FTP) sensor.
|
Fuel Tank Rated Capacity
|
Ignition ON
|
Varies
|
This parameter displays the capacity of the fuel tank in liters or gallons. The rated capacity displayed by the scan tool will varies with vehicle type.
|
Fuel Trim Learn
|
Engine Idling
|
Enabled / Disabled
|
This parameter displays Enabled when conditions are appropriate for enabling long term fuel trim corrections. This indicates that the long term fuel trim is adapting continuing amounts of short term fuel trim. If the diagnostic tool shows Disabled, then long term fuel trim will not respond to changes in short term fuel trim.
|
Fuel Trim Memory Cell
|
Engine Idling
|
Counts 0 250
|
This Parameter displays long term fuel corrections that is active based upon the current operating conditions (MAP, engine speed, purge duty cycle, A/C compressor state, and transmission range).
|
Fuel Trim System Test State
|
Engine Idling
|
Disabled / Running/EVAP Purge Test Running / Complete
|
This Parameter displays the current state of the fuel adjustment system diagnostic.
|
Fuel Volatility
|
Engine Idling
|
Varies
|
This parameter indicates the rate the fuel can be vaporized in the cylinder as calculated by the control module. The scan tool will display HIGH when the fuel volatility is high. The scan tool will display LOW when the fuel volatility is low.
|
Generator Indicator Command
|
Engine Idling
|
ON / OFF
|
This Parameter displays ON or OFF associated with the status of the generator.
|
Generator F Terminal Signal
|
Engine Idling
|
0-100 %
|
This parameter displays the amount of generator ON-time as commanded by the control module. The higher the percentage the greater the generator output.
|
Generator L Terminal Circuit High Voltage Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the generator L circuit terminal. The parameter displays Fault if the generator L circuit is shorted to voltage.
|
Generator L Terminal Circuit Low Voltage Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the generator L circuit terminal. The parameter displays Fault if the generator L circuit is shorted to ground.
|
Generator L Terminal Circuit Open Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the generator L circuit terminal. The parameter displays Fault if the generator L circuit is open.
|
Generator L Terminal Command
|
Engine Idling
|
0-100 %
|
This parameter displays the control modules commanded state of the voltage regulator on the generator.
|
HO2S 1
|
Engine Idling
|
50-900 mV
Varies
|
This parameter displays the voltage output from the HO2S to the control module. A lower voltage indicates a lean exhaust, while a higher voltage indicates a rich exhaust.
|
HO2S 1 Heater
|
Engine Idling
|
amps
|
This Parameter display the current feedback for the oxygen sensor heater output for sensor 1.
|
HO2S 1 Heater Control Circuit High Voltage Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the oxygen sensor heater control circuit. The parameter displays Fault if the oxygen sensor heater control circuit is shorted to voltage.
|
HO2S 1 Heater Control Circuit Low Voltage Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the oxygen sensor heater control circuit. The parameter displays Fault if the oxygen sensor heater control circuit is shorted to ground.
|
HO2S 1 Heater Control Circuit Open Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the oxygen sensor heater control circuit. The parameter displays malfunction if the oxygen sensor heater control circuit is open.
|
HO2S 2
|
Engine Idling
|
400-700 mV
|
This parameter displays the voltage output from the HO2S to the control module. A lower voltage indicates a lean exhaust, while a higher voltage indicates a rich exhaust.
|
HO2S 2 Heater
|
Engine Idling
|
amps
|
This Parameter display the current feedback for the oxygen sensor heater output for sensor 2.
|
HO2S 2 Heater Control Circuit High Voltage Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the oxygen sensor heater control circuit. The parameter displays Fault if the oxygen sensor heater control circuit is shorted to voltage.
|
HO2S 2 Heater Control Circuit Low Voltage Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the oxygen sensor heater control circuit. The parameter displays Fault if the oxygen sensor heater control circuit is shorted to ground.
|
HO2S 2 Heater Control Circuit Open Test Status
|
Engine Idling
|
OK / Malfunction / Not Run
|
This parameter displays the state of the oxygen sensor heater control circuit. The parameter displays malfunction if the oxygen sensor heater control circuit is open.
|
HO2S 1 or HO2S 2 Heater Command
|
Engine Idling
|
0-100 %
|
This parameter displays the HO2S heater ON time in percentage, as commanded by the control module.
|
HO2S 1 or HO2S 2 Heater Command
|
Engine Idling
|
ON / OFF
|
This parameter display the state of the HO2S heater control circuit as commanded by the control module.
|
HO2S Heater Monitor Complete This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This parameter displays the diagnostic monitor completion status during the current driving/monitoring cycle.
|
HO2S Heater Monitor Enabled This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This parameter displays the diagnostic monitor enable status during the current driving/monitoring cycle.
|
IAT Sensor 1
|
Engine Idling
|
-39° to +140°C
(-38° to +284°F)
|
This parameter displays the temperature of the air entering the air induction system based on input to the control module from the intake air temperature (IAT) sensor 1.
|
IAT Sensor 2
|
Engine Idling
|
-39° to +140°C
(-38° to +284°F)
|
This parameter displays the intake air temperature measured by a sensor that is located within the engine intake manifold.
|
Ignition 1 Signal
|
Ignition ON
|
B+
|
This parameter displays B+ when the control module detects a voltage at the ignition 1 input terminal.
|
Ignition Accessory Signal
|
Ignition ON
|
ON / OFF
|
This parameter displays ON when the control module detects a voltage at the ignition 1 input terminal.
|
Ignition Coil 1-4 Control Circuit High Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the state of the Ignition control circuit. The parameter displays Malfunction if the Ignition control circuit is shorted to voltage.
|
OK / Malfunction / Not Run
|
Ignition Coil 1-4 Control Circuit Low Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the state of the Ignition control circuit. The parameter displays Malfunction if the Ignition control circuit is shorted to ground.
|
OK / Malfunction / Not Run
|
Ignition Coil 1-4 Control Circuit Open Test Status
|
Engine Idling
|
OK
|
This parameter displays the state of the Ignition control circuit. The parameter displays Malfunction if the Ignition control circuit is open.
|
OK / Malfunction / Not Run
|
Ignition Coil Supply Voltage
|
Engine Idling
|
On
|
This parameter displays ON when voltage is supplied to the Ignition coil.
|
Ignition ON
|
ON / OFF
|
Ignition Cycles Since recommended Maximum Fuel Alcohol Content Exceeded
|
Ignition ON
|
Quantity
|
This Parameter displays the number of ignitions cycles since the most recent time that the Recommended Ethanol Concentration Exceeded failed. This Parameter value will reset when a code clear is performed. If a Recommended Ethanol Concentration Exceeded event has not taken place (either initially or after a code clear), this Parameter defaults to zero.
|
Ignition Cycles with Malfunction Since 1st Malfunction
|
Ignition ON
|
Quantity
|
This Parameter contains the number of ignition cycles with a failure reported since the first ignition cycle with a failure reported.
|
Ignition Cycles Without Completed Test Since 1st Malfunction
|
Ignition ON
|
Quantity
|
This parameter contains the number of ignition cycles without a failure reported since the first ignition cycle with a failure reported.
|
Ignition Cycles Without Malfunction Since Last Malfunction
|
Ignition ON
|
Quantity
|
This Parameter contains the number of ignition cycles with a pass reported and no failures reported since the first ignition cycle with a failure reported.
|
Ignition Timing
|
Engine Idling
|
Degrees
|
This parameter displays the final spark advance in terms of a crankshaft angle.
|
Immobilizer Auto Learn Counter
|
Ignition ON
|
Quantity
|
This parameter displays the number of auto learn cycles that have been successfully completed within the immobilizer system.
|
Immobilizer Automatic Learn Timer
|
Ignition ON
|
h/m/s
|
This Parameter displays the time elapsed within the current auto learn cycle within the immobilizer system.
|
Immobilizer Password Learn
|
Ignition ON
|
Enabled / Disabled
|
Learning Enabled indicates that learning of immobilizer code information is enabled.
|
Immobilizer Password Learn Scan Tool Delay
|
Ignition ON
|
Active / Inactive
|
Scan tool Learn Delay Active indicates that the security code has been accepted but the scan tool learn delay is active and will not allow learning enabled, programming security code, or resetting security code.
|
Immobilizer Security Code Accepted
|
Ignition ON
|
Yes / No
|
Security Code Accepted displaying Yes indicates that the received security code is correct.
|
Immobilizer Security Code Lockout
|
Ignition ON
|
Active / Inactive
|
Security Code Lockout Active indicates that the security code has not passed and lockout is active.
|
Immobilizer Security Code Lockout Active Timer
|
Ignition ON
|
ms
|
This Parameter displays the time elapsed since the immobilizer security code lockout has been activated either due to a battery disconnect or an incorrect immobilizer security code being entered.
|
Immobilizer Security Code Programmed
|
Ignition ON
|
Yes / No
|
Security Code Programmed indicates that the security code has been programmed.
|
Immobilizer Security Code Programming Counter
|
Ignition ON
|
Quantity
|
This Parameter displays the number of times a new immobilizer security code has been programmed through secure access. This counter can only be incremented.
|
Immobilizer Security Code Reset Counter
|
Ignition ON
|
Quantity
|
This Parameter displays the number of times the immobilizer security code has been reset to the default value through secure access. This counter can only be incremented.
|
Immobilizer Security Information Programmed
|
Ignition ON
|
Yes/No
|
This Parameter displays the status of the immobilizer system.
|
Immobilizer System Status
|
Ignition ON
|
Standby / Immobilized at Startup / Immobilized - No Response / Immobilized Negative Response / Immobilized -Incorrect Response / Post-Release State / Pre-Release State / Release State
|
This Parameter displays the status of the immobilizer system.
|
Immobilizer Valid Response Received Time
|
Ignition ON
|
ms
|
This Parameter displays the actual time observed for a valid immobilizer response.
|
Injector Duty Cycle
|
Engine Idling
|
0.82-1.50 ms
|
The parameter displays the amount of the fuel injector ON time or pulse width as commanded by the control module.
|
Intake Camshaft Position
|
Engine Idling
|
0 Degrees
|
This parameter displays the actual intake camshaft position in degrees.
|
Engine speed at 2000 RPM
|
10 Degrees
|
Intake Camshaft Position Variance
|
Engine Idling
|
0 Degrees
|
This parameter displays in degrees, the difference between the desired intake camshaft position and the actual intake camshaft position.
|
Engine speed at 2000 RPM
|
0 Degrees
|
Intake Camshaft Position Active Counter
|
Engine Idling
|
0-255
|
This parameter displays an incrementing counter when the control module receives a signal from the intake camshaft position sensor.
|
Intake Camshaft Position Commanded
|
Engine Idling
|
20 %
|
This parameter displays the ON-time or duty cycle of the intake camshaft position actuator solenoid valve as commanded by the control module.
|
Engine speed at 2000 RPM
|
50 %
|
Intake Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the state of the intake camshaft actuator solenoid control circuit. The parameter displays Malfunction if the camshaft actuator solenoid control circuit is shorted to ground.
|
Intake Camshaft Position Actuator Solenoid Valve Control Circuit Open Test Status
|
Engine Idling
|
OK
|
This parameter displays the state of the intake camshaft actuator solenoid control circuit. The parameter displays Malfunction if the camshaft actuator solenoid control circuit is open.
|
Intake Camshaft Position Actuator Solenoid Valve Control Circuit High Voltage Test Status Bank
|
Engine Idling
|
OK
|
This parameter displays the state of the intake camshaft actuator solenoid control circuit. The parameter displays Malfunction if the camshaft actuator solenoid control circuit is shorted to voltage.
|
Intake Manifold Pressure
|
Engine Idling
|
kPa
|
This parameter displays the engine intake manifold vacuum pressure calculated as the difference between ambient air pressure (barometric pressure) and intake manifold absolute pressure (MAP).
|
Knock Retard
|
Engine Idling
|
0 Degrees
|
This parameter indicates the amount of spark advance the control module removes from the ignition control (IC) spark advance in response to the signal from the knock sensors.
|
Long Term Fuel Trim
|
Engine Idling
|
0 %
|
This parameter displays the commanded Long Term Fuel Trim correction by the control module for bank 1 or bank 2 for cruise and acceleration conditions.
|
Long Term Fuel Trim Test Average
|
Engine Idling
|
0 %
|
This Parameter displays the filtered long term closed loop fuel correction for bank 1 or 2. This value is compared to thresholds to determine if the fuel adjustment system diagnostic is passing or failing or if an excess purge vapor test should be executed.
|
Long Term Fuel Trim Test Average Without Purge
|
Engine Idling
|
0 %
|
This Parameter displays the filtered non purge long term closed loop fuel correction for bank 1 or 2. This value is compared to thresholds to determine if the fuel adjustment system diagnostic is passing, failing, or indeterminate during normal purge-OFF operation as well as during the intrusive excess purge vapor test.
|
Low Engine Oil Pressure Indicator Command
|
Engine Idling
|
ON / OFF
|
This parameter displays the commanded state of the low EOP lamp control circuit by the control module.
|
Low Engine Oil Level Indicator Command
|
Engine Idling
|
Off
|
This parameter displays the commanded state of the Engine Oil Level Indicator.
|
MAP Performance Test 1
|
Engine Idling
|
OK / Malfunction
|
MAP Test 1 Residual Out of Tolerance indicates that the filtered MAP Test 1 residual (the difference between the measured intake manifold pressure and the intake manifold pressure predicted from the intake manifold model using the mass airflow predicted from the throttle model) exceeds a failure threshold.
|
MAP Performance Test 2
|
Engine Idling
|
OK / Malfunction
|
MAP Test 2 Residual Out of Tolerance indicates that the filtered MAP Test 2 residual (the difference between the measured intake manifold pressure and the intake manifold pressure predicted from the intake manifold model using the measured mass airflow) exceeds a failure threshold.
|
MAP Sensor
|
Engine Idling
|
kPa
|
This Parameter displays the actual engine intake manifold absolute pressure (MAP).
|
Volts
|
This PID contains the intake manifold absolute pressure (MAP) analog input as a percentage of its reference voltage.
|
MAF Sensor
|
Engine Idling
|
3.0-8.3 g/s
|
This parameter displays in grams per second, the measured quantity of air flowing into the engine during all operating conditions.
|
Engine speed at 2,500 RPM
|
11.88 g/s
|
Engine Idling
|
2,000-2,500 Hz
|
The diagnostic tool indicates an interval of 0-65.555 Hz.This parameter displays the frequency signal input to the control module and represents the measured quantity of air flowing into the engine during all operating conditions.
|
MIL Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Not Run
|
This parameter displays the state of the MIL control circuit. The parameter displays Fault if the MIL control circuit is shorted to ground.
|
MIL Control Circuit Open Test Status
|
Ignition ON
|
OK / Not Run
|
This parameter displays the state of the MIL control circuit. The parameter displays Fault if the MIL control circuit is open.
|
MIL Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Not Run
|
This parameter displays the state of the MIL control circuit. The parameter displays malfunction if the MIL control circuit is shorted to voltage.
|
MIL Command
|
Ignition ON
|
Off
|
This parameter displays the commanded state of the malfunction indicator lamp (MIL) control circuit by the control module.
|
Mil Requested by DTC
|
Ignition ON
|
Yes / No
|
This parameter indicates the reason the control module illuminated the MIL. The scan tool will display YES when the MIL is requested as a result of an A or B type DTC. The scan tool will display NO if the MIL is illuminated for another reason, such as transmission DTCs.
|
O2S / HO2S Monitor Complete This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This Parameter displays the enable and completion status during the current driving / monitoring cycle of each continuous legislated emission related monitor and non continuous legislated emission related monitor.
|
O2S / HO2S Monitor Enabled This Ignition Cycle
|
Engine Idling
|
Yes / No
|
This Parameter displays the enable and completion status during the current driving / monitoring cycle of each continuous legislated emission related monitor and non continuous legislated emission related monitor.
|
Park / Neutral Switch
|
Engine Idling
|
Park / Neutral
|
The scan tool shows the gear selector's position as e.g. Park/Neutral or Gear selected.
|
Power Enrichment
|
Engine Idling
|
Inactive
|
The scan tool displays ACTIVE or INACTIVE. ACTIVE displayed indicates that the ECM has detected conditions appropriate to operate in Power Enrichment mode. The ECM will command Power Enrichment mode when a large increase in throttle position and load is detected. While in Power Enrichment, the ECM will increase the amount of fuel delivered by entering Open Loop and increasing the injector pulse width. This is done to prevent a possible sag or hesitation from occurring during acceleration.
|
Power Moding
|
Ignition ON
|
OFF / Accessory / Run / Crank Request
|
This Parameter displays the state of the System Power Mode. This signal is based upon the state of the system power mode received over serial communication from the vehicle electronics. If the serial data signal not received, the Parameter will display OFF.
|
Recommended Maximum Fuel Alcohol Content
|
Engine Idling
|
%
|
This Parameter displays the recommended maximum fuel alcohol percentage for current vehicle conditions.
|
Recommended Maximum Fuel Alcohol Content Exceeded
|
Engine Idling
|
Yes / No
|
Recommended Ethanol Concentration Exceeded indicates that the fuel alcohol percentage has exceeded the recommended value for vehicle conditions.
|
Recommended Maximum Fuel Alcohol Content When Recommended Maximum Fuel Alcohol Content Exceeded
|
Engine Idling
|
%
|
This Parameter displays the recommended fuel alcohol percentage for vehicle conditions at the most recent time that the Recommended Ethanol Concentration Exceeded failed. This Parameter value will lock in until a code clear is issued to the controller. If a Recommended Ethanol Concentration Exceeded event has not taken place (either initially or after a code clear), this Parameter shall default to zero.
|
Reduced Engine Power
|
Engine Idling
|
Active / Inactive
|
This parameter displays Active if the control module is commanding reduced engine power due to a throttle actuator control (TAC) system condition.
|
Reduced Engine Power History
|
Ignition ON
|
Throttle Malfunction / Cooling Fan Malfunction / Engine Over-temperature Protection Active
|
This Parameter Displays the last reason that Powertrain has illuminated the Reduced Engine Power (REP) indication.
|
Redundant Odometer Memory
|
Ignition ON
|
Present / Not Present
|
ECU Odometer Programmed indicates if the ECU odometer value has been programmed.
|
Refueling Events Since Recommended Maximum Fuel Alcohol Content Exceeded
|
Ignition ON
|
Quantity
|
This Parameter displays the number of times the vehicle has been refueled since the most recent time that the Recommended Ethanol Concentration Exceeded failed. This Parameter value will reset when a code clear is issued to the controller. If a Recommended Ethanol Concentration Exceeded event has not taken place (either initially or after code clear), this Parameter defaults to zero.
|
Remaining Fuel in Tank
|
Ignition ON
|
%
|
This Parameter displays the total fuel level as a percentage of the rated capacity of the fuel tank.
|
Liter
|
This Parameter displays the actual total fuel volume contained in the fuel tank.
|
Secondary Air Injection Monitor Complete
|
Engine Idling
|
Yes/No
|
This parameter displays the completion status during the current driving/monitoring cycle of the non-continuous legislated emission related monitor. The states include Yes and No.
|
Secondary Air Injection Monitor Enabled
|
Engine Idling
|
Yes/No
|
This parameter displays the enable status during the current driving/monitoring cycle of the non-continuous legislated emission related monitor. The states include Yes or No.
|
Closed Loop
|
Engine Idling
|
-5 to +5 %
|
This parameter displays the short-term correction to the fuel delivery by the control module in response to oxygen sensor 1 or 2. If the oxygen sensor indicates a lean air/fuel mixture, the control module will add fuel increasing the short term fuel trim above 0. If the oxygen sensor indicates a rich air/fuel mixture, the control module will reduce fuel decreasing the short term fuel trim below 0.
|
Short Term Fuel Trim Test Average
|
Engine Idling
|
%
|
This Parameter displays the filtered short term closed loop fuel correction for HO2S Sensor 1. This value is compared to thresholds to determine if the fuel adjustment system diagnostic is passing or failing or if an excess purge vapor test should be executed.
|
Starter Relay Control Circuit Low Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the starter relay control circuit. The parameter displays malfunction if the starter relay control circuit is shorted to ground.
This parameter may not change if the scan tool is used to command the relay control circuit ON.
|
Starter Relay Control Circuit Open Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the starter relay control circuit. The parameter displays malfunction if the starter relay control circuit is open.
This parameter may not change if the scan tool is used to command the relay control circuit ON.
|
Starter Relay Control Circuit High Voltage Test Status
|
Ignition ON
|
OK / Malfunction / Not Run
|
This parameter displays the state of the starter relay control circuit. The parameter displays malfunction if the starter relay control circuit is shorted to voltage.
This parameter may not change if the scan tool is used to command the relay control circuit ON.
|
Starter Relay Command
|
Ignition switch not in the crank position
|
ON / OFF
|
This parameter indicates whether the control module is commanding the starter relay to go ON or OFF.
|
Ignition switch in the crank position
|
On
|
Start Up ECT
|
Ignition ON
|
-39° to +140°C (-38° to +284°F)
|
This parameter displays the temperature of the engine coolant on start-up based on input to the control module from the ECT sensor.
|
Start Up IAT
|
Ignition ON
|
-39° to +140°C (-38° to +284°F)
|
This parameter displays the temperature of the intake air at start in the air induction system based on input to the control module from the IAT sensor.
|
TAC Forced Engine Shutdown
|
Ignition ON
|
Yes / No
|
This parameter indicates the status of the TAC motor by the control module. The scan tool will display Yes if the engine has been shut down due to a throttle control fault.
|
TAC Motor
|
Ignition ON
|
Enabled / Disabled
|
This parameter indicates the status of the throttle actuator control (TAC) motor driver in the control module. The scan tool will display Enabled if TAC motor operation is allowed. The scan tool will display Disabled if the control module detects a condition that affects TAC motor operation.
|
TAC Motor Command
|
Ignition ON
|
%
|
This Parameter displays the commanded duty cycle for the throttle actuator output.
|
Throttle Body Idle Air Flow Compensation
|
Engine Idling
|
%
|
This Parameter displays the percent compensation of the Learned Airflow Variation Calibration. This value indicates the current amount of airflow compensation in response to engine intake airflow restrictions. It can also be used as feedback for the Learned Airflow Adapts Reset Trigger Device Control.
|
Throttle Position Performance Test
|
Engine Idling
|
OK / Malfunction
|
Throttle Position Residual Out of Tolerance indicates that the filtered throttle position residual (the product of the MAF residual and the MAP Test 1 residual) exceeds a failure threshold.
|
Total Knock Retard
|
Engine Idling
|
0°
|
This parameter displays how much ignition spark timing is being retarded due to all control systems monitored by the control module.
|
Total Misfire
|
Engine Idling
|
0
|
This parameter displays the total number of cylinder firing events that the control module detected as misfires for the last 200 crankshaft revolution sample period.
|
Throttle position
|
Ignition ON
|
0-100 %
|
This parameter displays the desired throttle position angle commanded by the control module.
|
Throttle Position Sensor 1
|
Ignition ON
|
3.7-4.3 V
|
This parameter displays the actual voltage on the throttle position sensor 1 signal circuit as measured by the control module.
|
Throttle Position Sensor 1 Learned Minimum
|
Ignition ON
|
4.1-4.7 V
|
This parameter displays the learned minimum value of throttle position sensor 1 as recorded by the control module during the last learn procedure.
|
Throttle Position Sensor 2
|
Ignition ON
|
0.7-1.1 V
|
This parameter displays the actual voltage on the throttle position sensor 2 signal circuit as measured by the control module.
|
Throttle Position Sensor 2 Learned Minimum
|
Ignition ON
|
0.5-0.9 V
|
This parameter displays the learned minimum value of throttle position sensor 2 as recorded by the control module during the last learn procedure.
|
Throttle Position Sensors 1 and 2
|
Ignition ON
|
Agree / Disagree
|
This parameter displays Disagree when the control module detects that throttle position sensor 1 voltage signal is not within the correct relationship to throttle position sensor 2. The scan tool displays Agree under the normal operating conditions.
|
Throttle Position Sensors 1 and 2 Position
|
Engine Idling
|
%
|
These parameters provide the percentage of the total travel or displacement of the sensor accounting for consideration of the learned minimum position. Also these parameters should always indicate 0 % at closed throttle and 100 % or near 100 % at wide open throttle.
|
Traction Control Status
|
Ignition ON
|
Active / Inactive
|
This parameter displays Active if the electronic brake and traction control module (EBTCM) is commanding traction control.
|
Torque Delivered Signal
|
Vehicle Moving
|
Nm
|
This Parameter displays the engine torque based upon the airflow through the engine and the torque losses due to spark retard and fuel shutoff. Since this is a steady state engine torque, it does not include the inertial component of engine torque.
|
Torque Management Ignition Timing Retard
|
Engine Idling
|
Degrees
|
This Parameter displays the total spark retard (in terms of a crankshaft angle).
|
Torque Request Inhibit-Fuel
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Torque Request Inhibit-Ignition Timing
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Torque Request Inhibit-Ignition Timing Advance
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Torque Request Inhibit-Minimum Idle
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Torque Request Inhibit-Minimum Torque
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Torque Request Inhibit-TAC
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Torque Request Inhibit-TAC Limit
|
Engine Idling
|
Yes / No
|
This Parameter displays the existing condition in the ECM causing the transmission torque request to be limited.
|
Turbocharger Bypass Solenoid Valve Command
|
Engine Idling
|
Boost/Bypass
|
This parameter shows the state of the turbocharger bypass solenoid. The scan tool shows either Boost or Bypass.
|
Turbocharger Bypass Solenoid Valve Control Circuit High Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the diagnostic state of the output driver for the turbocharger bypass solenoid. The scan tool will display OK if the circuit is operating correctly. The scan tool will display malfunction if there is a short to ground on the circuit.
|
Turbocharger Bypass Solenoid Valve Control Circuit Low Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the diagnostic state of the output driver for the turbocharger bypass solenoid. The scan tool will display OK if the circuit is operating correctly. The scan tool will display malfunction if there is a short to ground on the circuit.
|
Turbocharger Bypass Solenoid Valve Control Circuit Open Test Status
|
Engine Idling
|
OK
|
This parameter displays the diagnostic state of the output driver for the turbocharger bypass solenoid. The scan tool will display OK if the circuit is operating correctly. The scan tool will display malfunction if there is an open on the circuit.
|
Turbocharger Wastegate Solenoid Valve Command
|
Engine Idling
|
0%
|
This parameter shows the percent of the pulse width modulated (PWM) duty cycle that the wastegate solenoid is commanded.
|
Turbocharger Wastegate Solenoid Valve Control Circuit High Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the diagnostic state of the output driver for the turbocharger wastegate solenoid. The scan tool will display OK if the circuit is operating correctly. The scan tool will display Malfunction if there is an short to voltage in the circuit.
|
Turbocharger Wastegate Solenoid Valve Control Circuit Low Voltage Test Status
|
Engine Idling
|
OK
|
This parameter displays the diagnostic state of the output driver for the turbocharger wastegate solenoid. The scan tool will display OK if the circuit is operating correctly. The scan tool will display malfunction if there is a short to ground on the circuit.
|
Turbocharger Wastegate Solenoid Valve Control Circuit Open Test Status
|
Engine Idling
|
OK
|
This parameter displays the diagnostic state of the output driver for the turbocharger wastegate solenoid. The scan tool will display OK if the circuit is operating correctly. The scan tool will display malfunction if there is an open on the circuit.
|
VIN Programming Counter
|
Ignition ON
|
Quantity
|
This Parameter displays the number of times the VIN has been programmed. This counter can only be incremented.
|
Vehicle Speed Sensor
|
Vehicle Moving
|
km/h (mph)
|
This parameter displays the speed of the vehicle as calculated by the transmission control module (TCM) from information received from the vehicle speed sensor (VSS).
|
Warm-ups Since DTC Cleared
|
Ignition ON
|
Quantity
|
This parameter indicates the number of warm up cycles that have occurred Since DTCs were cleared. The scan tool will display a higher counts as more warm up cycles have occurred since the DTCs were cleared.
|
Warm Ups without Emission Malfunctions
|
Ignition ON
|
Quantity
|
This Parameter displays the number of OBD defined warm up cycles since the last emissions related (fault type A or B) fail report or MIL request. Emissions related DTCs are cleared from memory when this counter reaches 40.
|
Warm Ups without Non Emission Malfunctions
|
Ignition ON
|
Quantity
|
This Parameter displays the number of OBD defined warm up cycles since the last non emissions related (fault type C) fail report. Non emissions related DTCs are cleared from memory when this counter reaches 40.
|
Wide Open Throttle
|
Ignition ON
|
Yes / NO
|
This parameter displays the throttle status commanded by the control module. The scan tool will display YES if the vehicle throttle is commanded to 100 percent.
|