SAAB WIS ONLINE

DTC 71 SHIFT SOLENOID 1

DTC 71 SHIFT SOLENOID 1

DIAGNOSIS:

The output signal circuit of shift solenoid 1 is open or shorted.

TROUBLE SYMPTOM:

Does not shift.

WIRING DIAGRAM:


CHECK HARNESS CONNECTOR BETWEEN TCM AND TRANSMISSION.

Turn the ignition switch to OFF.

Disconnect the connector from TCM and transmission.

Measure the resistance of harness between TCM and shift solenoid 1 connector.

Connector & terminal

(B54) No. 22 — (B11) No. 1:

Is the resistance less than 1 Ω?

Yes


No

Repair the open circuit in harness between TCM and transmission connector.


CHECK HARNESS CONNECTOR BETWEEN TCM AND TRANSMISSION.

Measure the resistance of harness between TCM connector and chassis ground.

Connector & terminal

(B54) No. 22 — Chassis ground:

Is the resistance more than 1 MΩ?

Yes


No

Repair the short circuit in harness between TCM and transmission connector.


CHECK SHIFT SOLENOID 1.

Measure the resistance between transmission connector terminals.

Connector & terminal

(T4) No. 1 — No. 16:

Is the resistance 10 — 16 Ω?

Yes


No


CHECK OUTPUT SIGNAL EMITTED FROM TCM.

Connect the connectors to TCM and transmission.

Turn the ignition switch to ON (engine OFF).

Move the select lever to “D” range.

Measure the voltage between TCM connector and chassis ground.

Connector & terminal

(B54) No. 22 (+) — Chassis ground (−):

Is the voltage more than 9 V?

Yes


No


CHECK OUTPUT SIGNAL EMITTED FROM TCM.

Move the select lever to “2” range.

Measure the voltage between TCM connector and chassis ground.

Connector & terminal

(B54) No. 22 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Yes

Even if the AT OIL TEMP warning light blinks, the circuit has returned to a normal condition at this time. A temporary poor contact of the connector or harness may be the cause. Repair the harness or poor contact in TCM.


No


CHECK POOR CONTACT.

Is there poor contact in shift solenoid 1 circuit?

Yes

Repair poor contact.


No

Replace the TCM.


CHECK SHIFT SOLENOID 1 (IN TRANSMISSION).

Remove the transmission connector from bracket.

Lift-up the vehicle and support with rigid rack.

Note

Raise all wheels off ground.


Drain the ATF.

Important

Do not drain the ATF until it cools down.


Remove the oil pan, and disconnect connector from shift solenoid 1.

Measure the resistance between shift solenoid 1 connector and transmission ground.

Terminals

No. 1 — Transmission ground:

Is the resistance 10 — 16 Ω?

Yes


No

Replace the shift solenoid 1.


CHECK HARNESS CONNECTOR BETWEEN SHIFT SOLENOID 1 AND TRANSMISSION.

Measure the resistance of harness between shift solenoid 1 and transmission connector.

Connector & terminal

(T4) No. 1 — (AT5) No. 1:

Is the resistance less than 1 Ω?

Yes


No

Repair the open circuit in harness between shift solenoid 1 and transmission connector.


CHECK HARNESS CONNECTOR BETWEEN SHIFT SOLENOID 1 AND TRANSMISSION.

Measure the resistance of harness between shift solenoid 1 connector and transmission ground.

Connector & terminal

(T4) No. 1 — Transmission ground:

Is the resistance more than 1 MΩ?

Yes

Even if the AT OIL TEMP warning light blinks, the circuit has returned to a normal condition at this time. A temporary poor contact of the connector or harness may be the cause. Repair the harness or connector in shift solenoid 1 and transmission.


No

Repair the short circuit harness between shift solenoid 1 and transmission connector.