Test readings, control module connections
| Test readings, control module connections |
| Scope |
The following pages contain values and directions for measuring transmission control module signals and levels.
| Points to remember |
| • |
Observe the test conditions, use your common sense when judging the readings obtained.
|
|
| • |
The specified readings are with the ignition in position ON unless stated otherwise.
|
|
| • |
First check that the control module is supplied with current and grounded.
|
|
| • |
Then check all sensor inputs and signals from other systems.
|
|
| • |
Finally, check the control module outputs. Remember that the readings do not indicate whether the actuator is in working order.
|
|
| • |
If any reading is not OK, consult the wiring diagram to trace the leads, connectors or components which ought to be checked more thoroughly.
|
|
| • |
The specified test readings refer to those obtained with a calibrated Fluke 88/97.
|
|
| • |
All readings are with warm engine/gearbox.
|
|
| • |
Test readings %(+) and ms(+) indicate the signal's pulse ratio and pulse duration. A test instrument capable of measuring pulse ratio and pulse width must be used. The sign denotes a positive trigger pulse, TRIG+.
|
|
|
Pin
|
Cable colour
|
Component/ Function
|
In/Out
|
Test conditions
|
Test between
|
Test reading
|
See
|
|
1
|
YE/GY
|
Battery voltage (+15 circuit)
|
In
|
Ignition ON
Ignition OFF |
1-B+
|
< 0.5 V
12 V |
|
|
2
|
WH/BK
|
Solenoid, Lock-up (SL)
|
Out
|
Activate with diagnostic tool
Lock-Up solenoid |
2-32
|
12 V
or 0 V |
|
|
3
|
|
No connection
|
|
|
|
|
|
|
4
|
BK/GN
|
Solenoid 2-3 (S2)
|
Out
|
Gear D
Winter mode ON Winter mode OFF |
4-32
|
0 V 12 V |
|
|
5
|
|
No connection
|
|
|
|||
|
6
|
BK/BU
|
NTC sensor for transmission fluid temperature
|
In
|
20°C
50°C 80°C |
6-32
|
2.3 V
1.7 V 1.0 V |
|
|
7
|
BN/OG
|
Switch, SPORT
|
In
|
Switch depressed
Switch not activated |
7-32
|
0 V
12 V |
|
|
8
|
|
No connection
|
|
|
|||
|
9
|
GN/RD
|
Engine speed
Connected but not used |
In
|
|
|
|
|
|
10
|
BH/WH
|
Idling speed compensation Drive signal
|
Out
|
Gear lever N
From N to D, 3, 2, 1 From N to R |
10-32
|
0 V
12 V 12 V |
|
|
11
|
BU/GY
|
CHECK GEARBOX warning lamp
|
Out
|
Activate with diagnostic tool
Check Gearbox ON Check Gearbox OFF or With ignition ON and lamp lit |
11-1
|
12 V 0 V 12 V for 3 s |
|
|
12
|
GN/WH
|
SPORT indicator lamp
|
Out
|
Activate with
diagnostic tool Sport lamp: Sport lamp ON Sport lamp OFF |
12-1
|
12 V 0 V |
|
|
13
|
VT/WH
|
Gear selector position sensor, pin A
|
In
|
Selector lever P, R, 3, 2
Selector lever N, D, 1 |
13-32
|
12 V
0 V |
|
|
14
|
GY
|
Gear selector position sensor, pin C
|
In
|
Selector lever D, 3, 2, 1
Selector lever P, R, N |
14-32
|
12 V
0 V |
|
|
15
|
RD/BU
|
Inductive sensor, output shaft speed
|
In
|
Engine ON
Raise the car, engage 1st gear and run it at 20 km/h *) |
15-30
|
1.1 V~
190 Hz |
|
|
16
|
RD/WH
|
Battery voltage (+30 circuit)
|
In
|
Ignition ON/OFF
|
16-B+
|
< 0.5 V
|
|
|
17
|
WH/GN
|
Pressure control solenoid (ST) Current supply
|
Out
|
Activate with diagnostic tool
Pressure control solenoid |
17-18
|
4.3 V
or 0.7 V |
|
|
18
|
BU
|
Pressure control solenoid (ST)
Current feedback |
In
|
Activate with diagnostic tool
Pressure control solenoid |
18-34
|
0.3 V
or 0.1 V |
|
|
19
|
BK/VT
|
Solenoid 1-2/3-4 (S1)
|
Out
|
Gear D
Winter mode ON Winter mode OFF |
19-32
|
12 V 0 V |
|
|
20
|
|
No connection
|
|
|
|
|
|
|
21
|
BU/YE
|
Data link K
|
In/Out
|
Diagnostic tool connected
Diagnostic tool disconnected |
21-32
|
10 V
0 V |
|
|
22
|
BU/YE
|
Switch, WINTER
|
In
|
Switch depressed
Switch not activated |
22-32
|
0 V
12 V |
|
|
23
|
|
No connection
|
|
|
|||
|
24
|
|
No connection
|
|
|
|||
|
27
|
RD/WH
|
WINTER control lamp
|
Out
|
Activate with diagnostic tool
Winter lamp: Winter lamp ON Winter lamp OFF |
27-1
|
12 V 0 V |
|
|
28
|
GN
|
Gear selector position sensor, pin B
|
In
|
Selector lever R, N, D, 3
Selector lever P, 2, 1 |
28-32
|
12 V
0 V |
|
|
29
|
WH/YE
|
Gear selector position sensor, pin D
|
In
|
Selector lever P, N, 3, 1
Selector lever R, D, 2 |
29-32
|
12 V
0 V |
|
|
30
|
YE
|
Ground, signal ground for inductive sensor
|
In
|
30-B-
|
< 0.1 V
|
|
|
|
31
|
BK
|
Ground
|
In
|
31-B-
|
< 0.1 V
|
|
|
|
32
|
BK
|
Ground
|
In
|
35-B-
|
< 0.1 V
|
|
|
|
33
|
|
No connection
|
|
|
|||
|
34
|
|
No connection
|
|
|
|||
|
35
|
|
No connection
|
|
|
|||
|
36
|
VT
|
Brake light switch
|
In
|
Brakes applied
Brakes not applied |
36-32
|
12 V
0 V |
|
|
37
|
YE
|
Kickdown switch
|
In
|
Accelerator pedal depressed
Accelerator pedal inactive |
37-32
|
0 V
12 V |
|
|
38
|
|
No connection
|
|
|
|||
|
2500±50 rpm
|
2.0 V
100 Hz 15% (+) 1.5 ms (+) |
||||||
|
Starter motor cranking
|
0.25-1.0 V
100 Hz 2-8.2%(+) 0.2-0.82 ms (+) |
||||||
|
40
|
|
No connection
|
|
|
|||
|
41
|
|
No connection
|
|
|
|||
|
42
|
|
No connection
|
|
|
|||
|
43
|
|
No connection
|
|
|
|||
|
44
|
YE
|
Ground, signal ground for inductive sensor
|
In
|
44-B-
|
< 0.1 V
|
|
|
|
45
|
YE/BK
|
Inductive sensor, input shaft speed
|
In
|
Idling speed
|
45-30
|
1.2-1.4 V~
160-200 Hz |
|
|
2500 rpm
|
2.2 V~500 Hz
|
*) The vehicle speed can be read using the diagnostic tool, menu "Read values" and "Output speed".
This project is supported by memberships and donations. If you use this site, please consider Joining SCNA and/or making a donation.
Our Friends
