SAAB WIS ONLINE

Test readings, control module connections

Test readings, control module connections




Scope

Values and directions for measuring the voltage levels in the control module are given under the relevant heading.

Remember


Note the test conditions and use common sense when assessing the test result.

The specified values are with the ignition ON unless otherwise stated.

First, check that the control module has a power supply and is grounded.

Then check all sensor inputs and signals from other systems.

Finally, check the control module outputs. Remember that the test readings do not indicate whether or not the actuator is in working order.

If any reading is not OK, consult the wiring diagram to trace the leads, connectors or components which should be checked more thoroughly.

The specified test readings refer to those obtained with a calibrated Fluke 88/97.

Test values %(+) and ms(+) indicate the pulse ratio and pulse rate of the signal respectively. A scan tool for measuring pulse ratio and pulse width respectively must be used. The (+) indicates positive trigger pulse, TRIG+.



Main unit connections (connectors A, B, C)


> =greater than ; < = less than ; ~ = alternating current

(LP: LOGIC PROBE P = select pulse ; p = visible pulses

Connector (A)

Pin No.

Lead colour

Component/

function

In/Out

Test conditions

Across

Test reading

See

1



No connection











2



No connection











3

BN/RD

Telephone mute

In

No telephone call.

3(A)-8(A)

4-6 V



Telephone call.

3(A)-8(A)

<2 V

4

BN/RD

Power supply +15

In

Ignition ON

4(A)-8(A)

B+



5

BK/WH

Trigger voltage

(electric antenna)

Out

Main unit on.

5(A)-8(A)

Audio system



6

GN/WH

Rheostat











7

RD

Power supply +30

In



7(A)-8(A)

B+



8

BK

Ground





8(A) - good grounding point

<0.5V





Connector (B)

Pin No.

Lead colour

Component/

function

In/Out

Test conditions

Across

Test reading

See

1

BK/GN

Loudspeaker Right Rear (+)

Out

Music playing.

1(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



2

BK/WH

Loudspeaker Right Rear (-)

Out

Music playing.

2(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



3

BK/BN

Loudspeaker Right Front (+)

Out

Music playing.

3(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



4

BN/RD

Loudspeaker Right Front (-)

Out

Music playing.

4(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



5

BN

Loudspeaker Left Front (+)

Out

Music playing

5(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



6

BN/GY

Loudspeaker Left Front (-)

Out

Music playing.

6(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



7

BN/WH

Loudspeaker Left Rear (+)

Out

Music playing

7(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system



8

BN

Loudspeaker Left Rear (-)

Out

Music playing.

8(B)-8(A)

0-10V AC. Dependent on volume control. The test reading should vary with the volume of the music

Audio system





Connector (C)

Pin No.

Lead colour

Component/

function

In/Out

Test conditions

Across

Test reading

See

1

BK/BN

Phone line input, ground

In

-

-

-



2

WH

I-BUS (-)

In/Out

Ignition ON

2(C)-8(A)

2-3 V



3

OG

Phone line input, signal

In

-

-

-



4

GN

I-BUS (+)

In/Out

Ignition ON

4(C)-8(A)

2-3 V



5



No connection











6



No connection











7

RD

Line input CD changer

Left (-)

In

Music playing

7(C)-9(C)

0-2 VAC. The test reading should vary with the volume of the music.

Audio system



8

BN

Line input CD changer

Right (-)

In

Music playing

8(C)-10(C)

0-2 VAC. The test reading should vary with the volume of the music.

Audio system



9

BU

Line input CD changer

Left (+)

In

Music playing

9(C)-7(C)

0-2 VAC. The test reading should vary with the volume of the music.

Audio system



10

GN

Line input CD changer

Right (+)

In

Music playing

10(C)-8(C)

0-2 VAC. The test reading should vary with the volume of the music.

Audio system