Anti-roll bar, LHD, 4WD
Anti-roll bar, LHD, 4WD |
To remove |
1. |
Place the wheel in a straight forward position using cloth tape on the instrument panel, for example.
|
2. |
Remove the upper bumper shell attachments.
|
3. |
Hang two
83 95 212 Straps
in place over the radiator member and the radiator unit so that they are accessible from below.
|
4. |
Raise the car.
|
5. |
Remove the rear nut (A) from the wing liner on the left-hand side.
|
6. |
Remove the spoiler shield.
|
7. |
Bind the radiator unit tightly with the straps.
|
8. |
Remove
Propeller shaft
|
9. |
Remove the bolts (A) holding the rear torque rod to the subframe.
|
10. |
Remove front torque rod (B).
|
11. |
Cars with xenon headlights
: Remove the level sensor (C) on the left-hand suspension arm.
|
12. |
Remove the steering gear from the subframe (D). Mind the nuts and washers. Allow the steering gear to remain suspended.
|
13. |
Open the clips (A) that secure the power steering pipe to the subframe.
|
14. |
Set under
83 95 311 Trolley lift
with
83 94 801 Parent fixture
and
83 96 137 Centring tool, subframe - body
|
15. |
Remove the front section of the wing liners (A), and fold aside slightly.
|
16. |
Remove the subframe bolts (B) on both sides. Remove the stays (C) from the body.
|
17. |
Lower the subframe slightly.
|
18. |
Remove the anti-roll bar (D) from the subframe.
|
19. |
Remove the anti-roll bar links from the anti-roll bar (A).
Hold with a thin 17mm open wrench. |
20. |
Lower the subframe until the anti-roll bar can be extracted, the right-hand side first (A).
|
To fit |
1. |
Insert the anti-roll bar, left-hand side first (A).
|
2. |
Fit the anti-roll bar links (A) to the anti-roll bar. Hold with a thin 17 mm open wrench.
|
3. |
Fit the anti-roll bar (D) to the subframe.
|
4. |
Lift the subframe into place. Insert the bolts for the subframe and stays on both sides. Check that the pins on both sides of the radiator are correctly seated in the subframe's holder. Apply Vaseline to the rubber guides.
|
5. |
Raise the subframe using
83 95 311 Trolley lift
with
83 94 801 Parent fixture
and
83 96 137 Centring tool, subframe - body
. Fit the tool in the guide holes in the body. Fit the stays (C) and bolts (B).
Tightening torque 75 Nm +135° (55 lbf ft +135°) |
6. |
Lower and pull away the trolley lift.
|
7. |
Tighten the rear stay bolts.
Tightening torque 90 Nm +45° (66 lbf ft +45°) |
8. |
Fit the front section of the wing liners (A).
|
9. |
Close the clips (A) that secure the power steering pipe to the subframe.
|
10. |
Fit the anti-roll bar to the subframe (D).
|
11. |
Cars with xenon headlights
: Install the level sensor (C) on the left-hand suspension arm.
|
12. |
Install front torque rod (B).
|
13. |
Install the bolts (A) holding the rear torque rod to the subframe.
Tightening torques: M10 65 Nm (48 lbf ft) M12 120 Nm (88 lbf ft) |
14. |
Install
Propeller shaft
.
|
15. |
Remove radiator unit straps.
|
16. |
Fit the spoiler shield.
|
17. |
Lower the car to the floor.
|
18. |
Fit the upper bumper shell attachments.
|