Rear Suspension Support Replacement (FWD)
Rear Suspension Support Replacement (FWD) |
Special Tools
EN 49411 Angle MeterFor equivalent regional tools, refer to Special Tools .
Removal Procedure
1. |
Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
|
2. |
Remove the rear tire and wheel assemblies. Refer to
Tire and Wheel Removal and Installation
.
|
3. |
Remove the rear muffler assembly. Refer to
Exhaust Muffler Replacement (LAU)
Exhaust Muffler Replacement (LF1)
.
|
4. |
Disconnect the stabilizer shaft from stabilizer shaft links. Refer to
Stabilizer Shaft Replacement
.
|
5. |
Remove the left park brake cable from the support. Refer to
Parking Brake Rear Cable Replacement - Left Side (Front Wheel Drive)
Parking Brake Rear Cable Replacement - Left Side (All Wheel Drive)
.
|
6. |
Remove the right park brake cable from the support. Refer to
Parking Brake Rear Cable Replacement - Right Side (FWD)
Parking Brake Rear Cable Replacement - Right Side (All Wheel Drive)
.
|
7. |
Remove the rear axle lower control arms from the vehicle. Refer to
Rear Axle Lower Control Arm Replacement
.
|
8. |
Remove the adjust links from the from the vehicle. Refer to
Adjust Link Replacement
.
|
9. |
Remove rear axle upper control arm inner fasteners. Refer to
Rear Axle Upper Control Arm Replacement
.
|
10. |
Position a transmission jack under the rear support and firmly secure the support to the jack with straps.
|
11. |
Mark the position of the support to the body with spray paint.
|
12. |
Remove the support bolts and discard them.
|
13. |
With the aid of an assistant, lower the support from the transmission jack stand.
|
14. |
Remove the stabilizer shaft from the rear support.
|
Installation Procedure |
1. |
Install the stabilizer shaft assembly on to the support. Refer to Stabilizer Shaft Replacement . |
2. |
With the aid of an assistant, position the rear support onto the transmission jack and firmly secure the support to the jack with straps.
|
3. |
Refer to
Fastener Caution
.
Using the EN-49411 angle meter , install the NEW support bolts and tighten to: . |
• |
First Pass:
100 Nm (74 lb ft)
|
• |
Final Pass:
plus 90 degrees
|
4. |
Remove the transmission jack.
|
5. |
Install the rear axle upper control arm inner fasteners. Refer to
Rear Axle Upper Control Arm Replacement
.
|
6. |
Install the adjust links to the support. Refer to
Adjust Link Replacement
.
|
7. |
Install the rear axle lower control arms. Refer to
Rear Axle Lower Control Arm Replacement
.
|
8. |
Install the left park brake cable to the support. Refer to
Parking Brake Rear Cable Replacement - Left Side (Front Wheel Drive)
Parking Brake Rear Cable Replacement - Left Side (All Wheel Drive)
.
|
9. |
Install the right park brake cable to the support. Refer to
Parking Brake Rear Cable Replacement - Right Side (FWD)
Parking Brake Rear Cable Replacement - Right Side (All Wheel Drive)
.
|
10. |
Install the rear muffler assembly. Refer to
Exhaust Muffler Replacement (LAU)
Exhaust Muffler Replacement (LF1)
|
11. |
Connect the stabilizer shaft links to the stabilizer shaft. Refer to
Stabilizer Shaft Replacement
.
|
12. |
Install the rear tire and wheel assemblies. Refer to
Tire and Wheel Removal and Installation
.
|
13. |
Lower the vehicle.
|
14. |
Realign the rear suspension. Refer to
Wheel Alignment Measurement
.
|