SAAB WIS ONLINE

Wiring harness, rear 4D

Wiring harness, rear 4D


To remove


1. Remove all Side sill scuff plates .

2. Remove both Front seats .

3. Remove the Centre console .

4. Remove the Glove box .

5. Remove the data link connector. (A)


6. Remove the lower section of the dashboard with air duct on the driver's side.

7. Detach the floor lighting in the lower panel.

8. Remove the Seat cushion, rear seat

9. Remove the Backrest, rear seat, 4D .

10. Remove the nut (A) for the lower rear seat-belt anchorage point on both sides.


11. Remove the C-pillar trim, 4D on both sides.

12. Remove the Parcel shelf trim, 4D .

13. Remove the Scuff plate, luggage compartment, 4D .

14. Remove the Luggage compartment trim, floor panel, 4D .

15. Remove the Luggage compartment trim, side trim, 4D on both sides.

16. Remove the mat's weld screw nut (A) on the driver's side.


17. Remove the mat's two-stage rivets (B) on the driver's side.

18. Remove the mat's weld screw nut (C) on the passenger side.


19. Remove the mat's two-stage rivets (D) on the passenger side.

20. Remove the front floor mats.

21. Undo the nuts for the air duct on both sides.

22. Remove the air duct on both sides.

23. Remove the rear floor mat.

24. Remove the mounting plate for the left-hand sill scuff plate (A).


25. Remove the bracket for connector housings H-80, H43-1 and H43-2 (B).

26. Detach the connector housings H-80, H43-1 and H43-2 (C).

27. Detach the white connector housing (A) to the front harness from the bracket.


28. Remove the DICE control module (A) and detach the connector housing for DICE.


29. Detach connector housing H-33 (B) and remove the DICE control module's bracket.

30. LHD: Remove the switches (A).


31. LHD: Remove the fuse holder (B).

32. LHD: Fold down the fuse holder and the wiring harness for the switches.

33. Disconnect the ground cable (A) from grounding point G33.


34. Unplug and separate the connector for the left-hand front door.


35. Remove the left-hand side direction indicators.

36. Remove the rubber grommet for the left-hand front door's wiring harness and route the wiring harness into the passenger compartment (A).


37. Detach the rubber grommet and thread through the side direction indicator (B) wiring harness.

38. Remove the front left-hand speaker grille.

39. Remove the Headlining, 4D .

40. Remove the roof console (A) and unplug the connector (B) and remove any sunroof switch.


41. Cars with sunroof: Unplug the connector for the sunroof motor (A).


42. Remove the wiring harness from the upper windscreen (B).

43. Remove the wiring harness from the left-hand A-pillar (C).

44. Carefully route the wiring harness down through the instrument panel.

45. Detach the wiring harness duct from the left-hand front sill (A).


46. Detach the connector housings in the left-hand B-pillar, the door switch (B), for the rear door harness (C) and the seat-belt tensioner (D).

47. Detach the wiring harness clips from the B-pillar (E).

48. Detach the wiring harness duct at the left-hand rear door (A) and remove the grounding point (B) by the rear seat. Detach the fixings (C) and detach the door switch's (D) connector housing.


49. Detach the connector housing for the right and left-hand rear lamp (A).


50. Unplug and separate the connector for the tailgate harness (B).

51. Remove the grounding point under the left-hand rear lamp.

52. Release all wiring harness clips from the body in the luggage compartment.

53. Cars with SPA: Remove the Bumper, rear 4D .

54. Cars with SPA: Detach the rubber grommet for the wiring harness SPA (A).


55. Unplug the left-hand speaker's connector (A).


56. Unplug the connector for the parcel shelf lighting (B).

57. Unplug and separate the connector for the right-hand front door (A).


58. Remove the right-hand side direction indicators.

59. Remove the rubber grommet for the side direction indicator wiring harness and route the wiring harness into the passenger compartment (A).


60. Remove the rubber grommet for the right-hand front door's wiring harness and route the wiring harness into the passenger compartment (B).

61. Cars with PMM: Unplug the connector for the mirror memory (A).


62. Lift up the front right-hand noise insulation panel and detach the wiring harness from its fixings (A) along the sill and seat member.


63. Detach the wiring harness fixings in the B-pillar (A) and then detach the connector housings in the right-hand B-pillar, door switch (B), for rear door harness (C) and seat-belt tensioner (D).


64. Release the wiring harness from its fixings in the floor (A).


65. Remove grounding point G24 (B).

66. Detach the switch for the airbag control module (A), and detach the wiring harness fixing (B).


67. Detach the connector housings on the centre tunnel (C) and lift away the wiring harness for the panel.

68. Remove the weld screw nuts (A) for the wiring harness fixings above the centre tunnel.


69. Detach the connector housing for the TWICE control module (A).


70. Remove grounding point G14 (B).

71. Lift up the noise insulation panel and detach the wiring harness fixings (A) along the seat member and left-hand sill.


72. Remove the fuel tank, see WIS.

73. Detach the wiring harness mountings from the body.

74. Detach the tank harness rubber grommet from the body and route the harness into the passenger compartment (A).


75. Remove the rear wiring harness from the car.


To fit


1. Fit the new wiring harness in the car.

2. Route the tank harness through the body and fit the tank harness rubber grommet to the body (A).


3. Fit the wiring harness mountings to the body

4. Fit the fuel tank, see WIS.

5. Lift up the noise insulation panel and attach the wiring harness (A) along the seat member and left-hand sill.


6. Fit grounding point G14 (B).


7. Plug in the connector for the TWICE control module (A).

8. Fit the weld screw nuts (A) for the wiring harness fixings above the centre tunnel.


9. Attach the connector housings on the centre tunnel (C).


10. Attach the switch for the airbag control module (A), and attach the wiring harness fixing (B).

11. Fit grounding point G24 (B).


12. Position the wiring harness on the right-hand B-pillar and attach the fixings to the floor (A).

13. Attach the wiring harness fixings to the B-pillar (A). Attach the connector housings on the B-pillar, door switch (B), for rear door harness (C) and seat-belt tensioner (D).


14. Lift up the front right-hand noise insulation panel and attach the wiring harness fixings (A) along the sill and seat member.


15. Thread through the wiring harness for the side direction indicators and fit the rubber grommet (A).


16. Thread through the wiring harness for the right-hand front door and fit the rubber grommet (B).

17. Cars with PMM: Plug in the connector for the mirror memory (A).


18. Plug in the connector for the right-hand front door (A).


19. Fit the right-hand side direction indicators.

20. Connect the left-hand speaker (A).


21. Plug in the connector for the parcel shelf lighting (B).

22. Fit all wiring harness clips to the body in the luggage compartment.

23. Cars with SPA: Fit the Bumper, rear 4D .

24. Cars with SPA: Thread out the wiring harness for SPA and fit the rubber grommet (A).


25. Plug in the connector for the right and left-hand rear lamp (A).


26. Plug in the connector for the tailgate harness (B).

27. Fit the grounding point under the left-hand rear lamp.

28. Attach the wiring harness duct for the left-hand rear door (A), fit the grounding point (B) by the rear seat. Attach the wiring harness fixings (C) and fit the door switch (D).


29. Fit the wiring harness duct to the left-hand sill (A).


30. Attach the connector housings to the left-hand B-pillar, the door switch (B), for the rear door harness (C) and the seat-belt tensioner (D).

31. Attach the wiring harness clips to the B-pillar (E).

32. Carefully route the wiring harness up through the instrument panel.

33. Fit the wiring harness to the left-hand A-pillar (C)


34. Fit the wiring harness along the windscreen (B).

35. Plug in the connector for the sunroof motor (A).

36. Plug in the connector (B), and fit the sunroof switch (C) and the roof console (A).


37. Fit the parcel shelf trim.

38. Fit the Headlining, 4D .

39. Fit the C-pillar trim, 4D on both sides.

40. Fit the front left-hand speaker grille.

41. Thread through the wiring harness for the side direction indicators (B) and fit the rubber grommet.


42. Thread through the wiring harness to the left-hand front door and fit the rubber grommet for the wiring harness (A).

43. Fit the left-hand side direction indicators.

44. Plug in the connector for the left-hand front door.


45. Connect the ground cable for grounding point G-33 (A).


46. LHD: Fit the fuse holder panel in place. Route the wiring harness up to the switch.

47. LHD: Fit the switches (A).


48. Fit the fuse holder (B).

49. Plug in the connector and fit the control module for DICE (A).


50. Plug in connector H-33 (B) and fit the bracket for the DICE control module.

51. Attach the white connector (A) from the front harness to the bracket.


52. Fit the bracket (B) for connector housings H-80, H43-1 and H43-2.


53. Attach the connector housings H-80, H43-1 and H43-2 (C).

54. Fit the mounting plate for the sill scuff plate (A).

55. Fit the rear floor mat.

56. Fit the floor air duct on both sides.

57. Fit the nut for the floor air duct on both sides.

58. Fit the front floor mat on both sides.

59. Fit the two-stage rivet (D) on the passenger side.


60. Fit the weld screw nut (C) on the passenger side.

61. Fit the two-stage rivets (B) on the driver's side.


62. Fit the weld screw nut (A) on the driver's side.

63. Fit the Luggage compartment trim, side trim, 4D on both sides.

64. Fit the Luggage compartment trim, floor panel, 4D .

65. Fit the Scuff plate, luggage compartment, 4D .

66. Fit the nut (A) for the lower rear seat-belt anchorage point on both sides.

Tightening torque: 45 Nm (33 lbf ft).


67. Fit the Backrest, rear seat, 4D .

68. Fit the Seat cushion, rear seat .

69. Fit the floor lighting in the lower panel on the driver's side.

70. Fit the data link connector to the lower panel (A).


71. Fit the lower section of the dashboard with air duct on the driver's side.

72. Fit the Glove box .

73. Fit the Centre console .

74. Fit both Front seats .

75. Fit all Side sill scuff plates .