SAAB WIS ONLINE

Base Engine Misfire without Internal Engine Noises (LDK, LHU)

Base Engine Misfire without Internal Engine Noises (LDK, LHU)


Cause Correction
Abnormalities, severe cracking, bumps, or missing areas in the accessory drive belt

Malfunctions in the auxiliary drive system and the components can cause fluctuations in the engine speed which may be registered as a fault code for misfiring. A fault code for misfiring may be set without there actually having been any misfiring.

Replace the drive belt.

Worn, damaged, or mis-aligned accessory drive components or excessive pulley runout

May lead to a misfire DTC.

A misfire code may be present without an actual misfire condition.

Inspect the components, and repair or replace as required.

A loose or improperly installed engine flywheel or crankshaft balancer

A misfire code may be present without an actual misfire condition.

Repair or replace the flywheel and/or balancer, as required.

Restricted exhaust system

A serious blockage of the exhaust flow can cause significantly impaired engine performance which may be registered as a fault code. Possible causes of blockage are squashed or buckled pipes or clogged silencer and/or catalytic converter.

Repair or replace, as required.

Improperly installed or damaged vacuum hoses

Repair or replace, as required.

Improperly installed or leaking charge air cooler tube

Repair or replace, as required.

Improper sealing between the intake manifold and cylinder heads or throttle body

Replace the intake manifold, gaskets, cylinder heads, and/or throttle body, as required.

Improperly installed or damaged manifold absolute pressure (MAP) sensor or intake air pressure temp (TMAP) sensor

The sealing grommet of the MAP sensor should not be torn or damaged.

Repair or replace the MAP sensor and/or the TMAP sensor, as required.

Damage to the MAP sensor housing

Replace the intake manifold.

Worn or loose rocker arms

The rocker arm bearing end caps and/or needle bearings should be intact and in the proper position.

Replace the valve rocker arms as required.

Stuck valves

Carbon buildup on the valve stem can cause the valve not to close properly.

Repair or replace, as required.

Excessively worn or mis-aligned timing chain

Replace the timing chain and sprockets, as required.

Worn camshaft lobes

Replace the camshaft and valve lifters.

Excessive oil pressure

A lubrication system with excessive oil pressure may lead to excessive valve lifter pump up and loss of compression.


1. Check oil pressure. Refer to Oil Pressure Diagnosis and Testing .

2. Repair or replace the oil pump as required.


Faulty cylinder head gaskets and/or cracking or other damage to the cylinder heads and engine block cooling system passages

Coolant consumption may or may not cause the engine to overheat.


1. Inspect for spark plugs saturated by coolant.

2. Inspect the cylinder heads, engine block, and/or head gaskets.

3. Repair or replace, as required.


Worn piston rings

Oil consumption may or may not cause the engine to misfire.


1. Inspect the spark plugs for oil deposits.

2. Inspect the cylinders for a loss of compression. Refer to Engine Compression Test .

3. Perform cylinder leak down and compression testing to identify the cause.

4. Repair or replace, as required.


A damaged crankshaft reluctor wheel

A damaged crankshaft reluctor wheel can result in different symptoms depending on the severity and location of the damage.


Systems with electronic communications, DIS or coil per cylinder, and severe reluctor ring damage may exhibit periodic loss of crankshaft position, stop delivering a signal, and then re-sync the crankshaft position.

Systems with electronic communication, DIS or coil per cylinder, and slight reluctor ring damage may exhibit no loss of crankshaft position and no misfire may occur. However, a DTC P0300 may be set.

Systems with mechanical communications, high voltage switch, and severe reluctor ring damage may cause additional pulses and effect fuel and spark delivery to the point of generating a DTC P0300 or P0336.


Replace the sensor and/or crankshaft as required.