DTC P1400 FUEL TANK PRESSURE CONTROL SOLENOID VALVE CIRCUIT LOW

/ 9-2X (9346) / 2005 / 2. Engine / ENGINE (DIAGNOSTICS), 2.5i / Diagnostic Procedure with Diagnostic Trouble Code (DTC) / Fault diagnosis, fault codes / DTC P1400 FUEL TANK PRESSURE CONTROL SOLENOID VALVE CIRCUIT LOW

DTC DETECTING CONDITION:

•

Two consecutive driving cycles with fault

•

GENERAL DESCRIPTION

Important
After repair or replacement of faulty parts, conduct Clear Memory Mode and Inspection Mode .

WIRING DIAGRAM:

CHECK OUTPUT SIGNAL FROM ECM.

Turn ignition switch to ON.

Measure the voltage between ECM and chassis ground.

Connector & terminal

(B134) No. 12 (+) — Chassis ground (−):

Is the voltage more than 10 V?

Yes

CHECK FOR POOR CONTACT.

Check for poor contact in ECM connector.

Is there poor contact in ECM connector?

Yes

Repair poor contact in ECM connector.

Contact Service Center.

CHECK HARNESS BETWEEN FUEL TANK PRESSURE CONTROL SOLENOID VALVE AND ECM CONNECTOR.

Turn ignition switch to OFF.

Disconnect the connectors from fuel tank pressure control solenoid valve and ECM.

Measure the resistance of harness between fuel tank pressure control solenoid valve connector and chassis ground.

Connector & terminal

(R68) No. 2 — Chassis ground:

Is the resistance less than 10 Ω?

Yes

Repair short circuit to ground in harness between ECM and fuel tank pressure control solenoid valve connector.

CHECK HARNESS BETWEEN FUEL TANK PRESSURE CONTROL SOLENOID VALVE AND ECM CONNECTOR.

Measure the resistance of harness between ECM and fuel tank pressure control solenoid valve connector.

Connector & terminal

(B134) No. 12 — (R68) No. 2:

Is the resistance less than 1 Ω?

Yes

•

Repair harness and connector.

•

Note
In this case, repair the following:
•	Open circuit in harness between ECM and fuel tank pressure control solenoid valve connector
•	Poor contact in coupling connector

CHECK FUEL TANK PRESSURE CONTROL SOLENOID VALVE.

Measure the resistance between fuel tank pressure control solenoid valve terminals.

Terminals

No. 1 — No. 2:

Is the resistance 10 — 100 Ω?

Yes

Replace the fuel tank pressure control solenoid valve.

CHECK POWER SUPPLY TO FUEL TANK PRESSURE CONTROL SOLENOID VALVE.

Turn ignition switch to ON.

Measure the voltage between fuel tank pressure control solenoid valve and chassis ground.

Connector & terminal

(R68) No. 1 (+) — Chassis ground (−):

Is the voltage more than 10 V?

Yes

•

Repair harness and connector.

•

Note
In this case, repair the following:
•	Open circuit in harness between main relay and fuel tank pressure control solenoid valve connector
•	Poor contact in coupling connector
•	Poor contact in main relay connector

CHECK FOR POOR CONTACT.

Check for poor contact in fuel tank pressure control solenoid valve connector.

Is there poor contact in fuel tank pressure control solenoid valve connector?

Yes

Repair poor contact in fuel tank pressure control solenoid valve connector.

Contact Service Center.

DTC P1400 FUEL TANK PRESSURE CONTROL SOLENOID VALVE CIRCUIT LOW

CHECK OUTPUT SIGNAL FROM ECM.

Is the voltage more than 10 V?

CHECK FOR POOR CONTACT.

Is there poor contact in ECM connector?

CHECK HARNESS BETWEEN FUEL TANK PRESSURE CONTROL SOLENOID VALVE AND ECM CONNECTOR.

Is the resistance less than 10 Ω?

CHECK HARNESS BETWEEN FUEL TANK PRESSURE CONTROL SOLENOID VALVE AND ECM CONNECTOR.

Is the resistance less than 1 Ω?

CHECK FUEL TANK PRESSURE CONTROL SOLENOID VALVE.

Is the resistance 10 — 100 Ω?

CHECK POWER SUPPLY TO FUEL TANK PRESSURE CONTROL SOLENOID VALVE.

Is the voltage more than 10 V?

CHECK FOR POOR CONTACT.

Is there poor contact in fuel tank pressure control solenoid valve connector?

Our Friends