DTC B0967 or B0968
DTC B0967 or B0968 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B0967 02
Parking Aid On/Off Switch Circuit Short to Ground
DTC B0968 01
Parking Aid On/Off Switch Indicator Circuit Short to Battery
DTC B0968 06
Parking Aid On/Off Switch Indicator Circuit Low Voltage/Open
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Parking Assist Switch Indicator Ignition | B0968 06 | B0968 06 | - | - |
Parking Assist Switch Signal | B0967 02 | 1 | - | - |
Parking Assist Switch Indicator Control | B0968 06 | B0968 06 | B0968 01 | - |
Parking Assist Switch Ground | - | 1 | - | - |
1. Parking Assist Switch Malfunction |
Circuit/System Description |
The parking assist can be activated/deactivated by pressing the parking assist switch. By engaging the reverse gear the parking assist can also be activated. By subsequently pressing the parking assist switch the parking assist can be disabled again.
The indicator in the parking assist switch shows the status of the parking assist. If the lamp is ON, the parking assist is activated.
Conditions for Running the DTC |
• |
Ignition ON
|
• |
The parking assist is activated. The activation takes place by putting in the reverse gear or by pressing the parking assist switch.
|
Conditions for Setting the DTC |
B0967 02
The parking assist control module has detected a short to ground.B0968 01
The parking assist control module has detected a short to battery.B0968 06
The parking assist control module has detected a short to ground or open.Action Taken When the DTC Sets |
• |
The parking assist is disabled.
|
• |
The driver information center displays SERVICE PARK ASSIST.
|
Conditions for Clearing the DTC |
The condition for setting the DTC is no longer present.
Reference Information |
Schematic Reference
Object Detection Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Object Detection Description and Operation (UVC) Object Detection Description and Operation (UD5)
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification |
1. |
Verify that DTC B0967 02 is not present.
|
2. |
If DTC is present, refer to Parking Assist Switch Malfunction.
|
3. |
Verify that B0968 01 or B0968 06 is not present.
|
4. |
If DTC is present, refer to Parking Assist Switch Indicator Malfunction.
|
5. |
Activate and deactivate the parking assist switch and verify the scan tool Park Assist Switch parameter changes between Active and Inactive.
|
Circuit/System Testing |
Parking Assist Switch Circuit Malfunction
1. |
Ignition OFF, disconnect the harness connector at the S48D multi-function switch module - dashboard.
|
2. |
Test for less than 10 Ω between the ground circuit terminal 2 and ground.
|
3. |
If greater than the specified range, test the ground circuit for an open/high resistance.
|
4. |
Connect the harness connector at the S48D multi-function switch module - dashboard.
|
5. |
Disconnect the cable harness switch X1 at the front and rear control modules for Saab Park Assistance, K41.
|
6. |
Ignition ON, test for less than 0.3 V between the signal circuit terminal 8 X1 and ground.
|
7. |
If greater than the specified value, test the signal circuit for a short to voltage.
|
8. |
Ignition ON, verify that a test lamp does not illuminate between the B+ circuit terminal 1 X1 and signal circuit terminal 8 X1.
|
9. |
If the test lamp illuminates, test signal circuit for a short to ground. If the circuit tests normal, replace the S48D multi-function switch module - dashboard.
|
10. |
Verify that the test lamp illuminates between the B+ circuit terminal 1 X1 and signal circuit terminal 8 X1 while pressing the parking assist switch.
|
11. |
If the test lamp does not illuminate, test the signal circuit for an open/high resistance. If all circuits test normal, replace the S48D multi-function switch module - center console.
|
12. |
If all circuits test normal, replace the Front and Rear Parking Assist Control Modules, K41.
|
Parking Assist Switch Indicator Circuit Malfunction
1. |
Ignition OFF, disconnect the harness connector at the S48D multi-function switch module - dashboard.
|
2. |
Ignition ON, test for B+ between the ignition circuit terminal 3 and ground.
|
3. |
If less than the specified value, test the ignition circuit for a short to ground or an open/high resistance.
|
4. |
Command the Park Assist Switch LED output control ON with the scan tool. Test for B+ between the ignition circuit terminal 3 and the signal circuit terminal 6.
|
5. |
If less than the specified value, test the signal circuit for an open/high resistance. If all circuits test normal, replace the K41 parking assist control module.
|
6. |
Command the Park Assist Switch LED output control OFF with the scan tool. Test for less than 0.3 V between the ignition circuit terminal 3 and the signal circuit terminal 6.
|
7. |
If greater than the specified value, test the signal circuit for a short to ground. If all circuits test normal, replace the K41 parking assist control module.
|
8. |
If all circuits test normal, replace the S48D multi-function switch module - dashboard.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the repair.
• |
Accessory Switch Replacement
|
• |
Control Module References
for parking assist control module replacement, programming and setup
|