DTC B1019
DTC B1019 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptor |
DTC B1019 00
System Configuration Error
Circuit/System Description |
Inflatable restraint sensing and diagnostic module (SDM) monitors the number of safety components that have been installed on the vehicle. When the ignition is turned ON, the SDM evaluates the number of safety components installed and compares it to the number of components the SDM expects to see on the vehicle with its current calibration. If there is a mismatch between detected components and the components programmed with the SDM calibration, DTC B1019 will set. The components (if equipped) that the SDM will detect include inflatable restraint deployment loops, impact sensors, passenger presence system components, seat position sensors, disable switches, and seat belt switches.
Conditions for Running the DTC |
Ignition voltage is between 9-16 V.
Conditions for Setting the DTC |
The setup for the SDM has not been completed and the SDM does not detect the correct number of sensors or deployment loops than is expected with this calibration.
Action Taken When the DTC Sets |
• |
The SDM requests the instrument cluster to illuminate the AIR BAG warning indicator.
|
• |
The DTC must be cleared before running the setup SDM.
|
• |
Air bag indicator will continue to flash until SDM setup procedure is complete.
|
Conditions for Clearing the DTC |
• |
The condition for setting the DTC is no longer present.
|
• |
A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
|
Diagnostic Aids |
The SDM scan tool deployment loop and impact sensor data must match what the SDM has been programmed to expect to see on the vehicle. B1019 DTC will set if a deployment loop or impact sensor is added or removed from the system.
DTC B1019 will set when an open/high resistance DTC sets for a deployment loop or impact sensor. This causes mismatch between the learned and actual components connected to the SDM.
DTC B1019 can set with no other DTCs if an unused deployment loop or impact sensor circuit is shorted to ground. This causes a mismatch between the learned and actual components connected to the SDM.
Reference Information |
Schematic Reference
• |
Seat Belt Schematics
|
• |
SIR Schematics
|
Connector End View Reference
Component Connector End Views
Description and Operation
• |
Seat Belt System Description and Operation
|
• |
SIR System Description and Operation
|
Electrical Information Reference
• |
Circuit Testing
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Connector Repairs
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification |
Note | ||
DTC B1019 can set after SDM has been replaced and/or reprogrammed before the setup procedure is completed. The setup procedure cannot be completed if DTC B1019 is set as current or history. If a short or open is detected in a deployment circuit prior to the setup procedure being performed, the SDM will set DTC B1019. |
1. |
Ignition ON.
|
2. |
Verify no other SDM DTCs are set.
|
3. |
If other SDM DTCs are set
|
4. |
Diagnose those DTCs first. Refer to
Diagnostic Trouble Code (DTC) List - Vehicle
|
5. |
If no other SDM DTCs are set
|
6. |
Verify the impact sensors called out in the scan tool data list match the number of actual impact sensors the vehicle is built with.
|
7. |
If the number of impact sensors do not match
|
8. |
Verify the correct SDM calibration file is loaded in the SDM.
|
9. |
If the SDM calibration file is correct, the vehicle contains less/more sensors than it is supposed to. Modify the vehicle to match the SDM impact sensor calibration scan tool data list.
|
10. |
If the number of impact sensors match
|
11. |
Verify the enabled deployment loops called out in the scan tool data list match the deployment loops the vehicle is built with.
|
12. |
If the number of enabled deployment loops do not match
|
13. |
Verify the correct SDM calibration file is loaded in the SDM.
|
14. |
If the SDM calibration file is correct, modify the vehicle to match the SDM enabled deployment loop calibration scan tool data list.
|
15. |
If the number of enabled deployment loops match
|
16. |
Replace K36 Inflatable restraint sensing and diagnostic module (SDM).
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the repair.
• |
SIR/SRS Wiring Repairs
|
• |
Control Module References
for SDM replacement, programming and setup
|