DTC B2345 (Without Memory A45)
|
DTC B2345 (Without Memory A45)
|
DTC B2345 13
Seat Heater Disable Circuit Low Voltage High/Temperature
Diagnostic Fault Information
|
Circuit
|
Short to Ground
|
Open/High Resistance
|
Short to Voltage
|
Signal Performance
|
Driver Heated Seat Element Control Terminal 3 X2
|
B242A 02
|
B2425 0D
|
B242A 01
|
B2425 0E
|
Driver Heated Seat Element Control Terminal 1 X2
|
B242A 02
|
B2425 0D
|
B242A 01
|
B2425 0E
|
Driver Heated Seat Temperature Sensor Signal
|
B1925 02
|
B1925 05
|
B1925 05
|
B2345 13
|
Driver Heated Seat Temperature Sensor Low Reference
|
-
|
B1925 05
|
-
|
B2345 13
|
Passenger Heated Seat Element Control Terminal 5 X2
|
B242A 02
|
B2430 0D
|
B242A 01
|
B2430 0E
|
Passenger Heated Seat Element Control Terminal 2 X2
|
B242A 02
|
B2430 0D
|
B242A 01
|
B2430 0E
|
Passenger Heated Seat Temperature Sensor Signal
|
B2170 02
|
B2170 05
|
B2170 05
|
B2345 13
|
Passenger Heated Seat Temperature Sensor Low Reference
|
-
|
B2170 05
|
-
|
B2345 13
|
Circuit/System Description
|
The seat heating control module controls seat heating operation for both the driver and front passenger seats. The heating elements are controlled through individual high side and low side control circuits. The low side control circuits for both seats are connected to a common reference point internal to the module. This reference point is biased to approximately 2.5 V. Before the seat heating control module will allow heated seat operation, it checks to see if this biased voltage is shorted to ground or voltage. Once the module verifies that it is not closing to a shorted heating element, it allows for heated seat operation. The module will then continue to monitor the heating elements for a shorted circuit.
Conditions for Running the DTC
|
The seat heating control module must be powered.
Conditions for Setting the DTC
|
B2345 13
Any temperature sensor input that remains below 1.5 V for more than 1 second.
Action Taken When the DTC Sets
|
The heated seat function for both front seats will be disabled.
Conditions for Clearing the DTC
|
•
|
The current DTC will clear and set the code to history 3 seconds after the reference voltage returns to the normal operating range and the ignition is cycled OFF then back to ACC or RUN.
|
•
|
The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.
|
Schematic Reference
Heated/Cooled Seat Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Heated/Vented Seat Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for scan tool information
1.
|
Ignition OFF, disconnect the X2, X3 harness connectors at the K29 seat heating control module.
|
2.
|
Test for greater than 3.0 kΩ between the signal and the low reference circuits listed below:
|
|
•
|
E14B driver seat cushion terminal 3 X3 and terminal 13 X2
|
|
•
|
E14D passenger seat cushion terminal 4 X3 and terminal 14 X2
|
3.
|
If less than the specified value, test for a short between the signal and low reference circuits. If the circuits test normal, replace the appropriate E14 seat cushion heating element.
|
4.
|
If all circuits test normal, replace the K29 seat heating control module.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.