SAAB WIS ONLINE

DTC P2617

DTC P2617

Diagnostic Instructions


• Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

• Review Strategy Based Diagnosis for an overview of the diagnostic approach.

• Diagnostic Procedure Instructions provides an overview of each diagnostic category.


DTC Descriptor

DTC P2617 00

Crankshaft Position Signal Output Circuit

Diagnostic Fault Information

Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance
Crankshaft Position Sensor Signal

P2617 00

P2617 00

P2617 00

P0336 00

Low Reference

P2617 00

P2617 00

P2617 00

P0336 00



Circuit/System Description

The crankshaft position sensor signal indicates the crankshaft speed and position. The crankshaft position sensor produces an alternating current (AC) voltage of different amplitude and frequency. The frequency depends on the velocity of the crankshaft, and the AC voltage output depends on the crankshaft position and battery voltage. The engine control module (ECM) can synchronize ignition timing and fuel injector timing based on the crankshaft position sensor and the camshaft position sensor inputs. The crankshaft position sensor is also used to detect misfire and odometer display. The crankshaft position sensor circuits are connected directly to the ECM.

Conditions for Running the DTC


• The engine is cranking or operating.

• The DTC runs continuously once the above condition is met.


Conditions for Setting the DTC

The ECM detects 4 crankshaft position sensor resynchronizations within 5 s.

Action Taken When the DTC Sets

P2617 is a Type A DTC.

Conditions for Clearing the DTC

P2617 is a Type A DTC.

Diagnostic Aids

The following conditions can also set the DTC:


• Physical damage to the crankshaft position sensor or the reluctor wheel

• Excessive play or looseness of the crankshaft position sensor or the reluctor wheel

• Improper installation of the crankshaft position sensor or the reluctor wheel

• Excessive air gap between crankshaft position sensor and the reluctor wheel


Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Engine Control Module Description

Electrical Information Reference


• Circuit Testing

• Connector Repairs

• Testing for Intermittent Conditions and Poor Connections

• Wiring Repairs


DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References

Circuit/System Verification

Engine starting or running, observe the scan tool Engine Speed parameter. The reading should be between 50-850 RPM.

Circuit/System Testing


1. Ignition OFF, disconnect the harness connector at the B26 Crankshaft Position Sensor.

2. Ignition ON, test for 2.0-3.0 V between the low signal circuit terminal 2 and ground.

3. If greater than the specified range, test the low signal circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module.

4. If less than the specified range, test the low signal circuit for a short to ground or an open/high resistant. If the circuit tests normal, replace the K20 Engine Control Module.

5. Ignition ON, test for 2.0-3.0 V between the high signal circuit terminal 1 and ground.

6. If greater than the specified range, test the high signal circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module.

7. If less than the specified range, test the high signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K20 Engine Control Module.

8. If all circuits test normal, test or replace the B26 Crankshaft Position Sensor.


Component Testing


Static Test

1. Ignition OFF, disconnect the harness connector at the B26 Crankshaft Position Sensor.

2. Test for 700-800 Ω between the high signal terminal 1 and the low signal circuit terminal 2.

3. If not within the specified range, replace the B26 Crankshaft Position Sensor.

4. Test for infinite resistance between each terminal and the sensor housing/case.

5. If less than the specified value, replace the B26 Crankshaft Position Sensor.

6. Engine cranking, test for greater than 0.5 V alternating current between the high signal circuit terminal 1 and the low signal terminal 2.

7. If less than the specified range, replace the B26 Crankshaft Position Sensor.


Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.


• Crankshaft Position Sensor Replacement

• Engine Control Module Replacement