DTC B2455
DTC B2455 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B2455 00
Cellular Phone Microphone Circuit
DTC B2455 04
Cellular Phone Microphone Circuit Open
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Cellular Microphone Signal
|
B2455 00, B2455 04
|
B2455 00, B2455 04
|
B2455 00, B2455 04
|
-
|
Cellular Microphone Drain
|
-
|
B2455 00, B2455 04
|
1
|
-
|
1. OnStar Microphone Inoperative - Caller Cannot Be Heard
|
Circuit/System Description |
The telematics communication interface control module provides the cellular phone microphone with a supplied voltage on the cellular phone microphone signal circuit. When the microphone is in use, voice data from the user is sent back to the telematics communication interface control module on the signal circuit. The telematics communication interface control module provides a ground for the cellular phone microphone via the low reference wire.
Conditions for Running the DTC |
• |
The ignition must be in the RUN or ACC position.
|
• |
The system voltage is at least 9.5 V and no more than 15.5 V.
|
• |
All the above conditions are present for greater than 10 seconds.
|
Conditions for Setting the DTC |
• |
The telematics communication interface control module detects an open, short to ground or short to voltage in the cellular phone microphone signal circuit for 10 seconds or greater.
|
• |
The telematics communication interface control module detects an open/high resistance in the low reference circuit for 10 seconds or greater.
|
Action Taken When the DTC Sets |
• |
The OnStar® status LED turns red.
|
• |
The telematics communication interface control module will not receive a signal from the cellular phone microphone.
|
• |
Calls can be placed but the caller cannot be heard.
|
Conditions for Clearing the DTC |
• |
The condition responsible for setting the DTC no longer exists.
|
• |
A history DTC will clear once 50 consecutive malfunction-free ignition cycles have occurred.
|
Reference Information |
Schematic Reference
OnStar Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
OnStar Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing |
1. |
Ignition OFF, disconnect the harness connector at the B24 cellular phone microphone.
|
2. |
Ignition OFF and scan tool disconnected, wait until all retained accessory power is OFF, test for less than 10 Ω between the low reference circuit terminal 1 or A (depending on vehicle) and ground, allowing up to 5 minutes for the circuit resistance to drop to its lowest reading.
|
3. |
If greater than the specified range, test the circuit for an open/high resistance.
|
4. |
Ignition ON, test for 9.5-10.5 V between the signal circuit terminal 2 or B (depending on vehicle) and ground.
|
5. |
If less than the specified value, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K73 telematics communication interface control module.
|
6. |
If greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the K73 telematics communication interface control module.
|
7. |
If all circuit test normal, replace the B24 cellular phone microphone.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Mobile Telephone Microphone Replacement
|
• |
Control Module References
for telematics communication interface control module replacement, setup, and programming
|