DTC B1516
DTC B1516 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B1516 08
Battery Current Sensor Signal Invalid
DTC B1516 66
Battery Current Sensor Wrong Mounting Position
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
5 V Reference
|
B1516 08
|
B1516 08
|
-
|
-
|
Signal
|
B1516 08
|
B1516 08
|
B1516 08
|
B1516 08, B1516 66
|
Low Reference
|
-
|
B1516 08
|
-
|
-
|
Circuit/System Description |
The battery current sensor is a 3-wire hall effect current sensor. The body control module (BCM) supplies 5 V and ground to the battery current sensor. The battery current sensor measures the amount of current flowing to or from the battery, and supplies a pulse width modulation (PWM) signal to the BCM.
Conditions for Running the DTC |
B1516 08
The BCM is awake.B1516 66
• |
The BCM is awake.
|
• |
The engine is OFF.
|
Conditions for Setting the DTC |
B1516 08
The battery current signal is less than 4 percent or greater than 96 percent duty cycle for 2 minutes.B1516 66
The battery current polarity is positive for 2 minutes.Action Taken When the DTC Sets |
The regulated voltage control (RVC) is disabled.
Conditions for Clearing the DTC |
The DTC passes when the battery current returns to the normal range for 15 seconds.
Diagnostic Aids |
DTC B1516 08 could be set by overcharging with a battery charger or jump starting.
Reference Information |
Schematic Reference
Starting and Charging Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Charging System Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing |
B1516 08
1. |
Ignition OFF, disconnect the harness connector at the B18 battery current sensor.
|
2. |
Ignition OFF and scan tool disconnected, open and close the driver door. Wait 1 minute. Test for less than 30 Ω between the low reference circuit terminal B and ground.
|
3. |
If greater than specified range , test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K9 BCM.
|
4. |
Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.
|
5. |
If less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
|
6. |
If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
|
7. |
Ignition ON, test for 4.8-5.2 V between the signal circuit terminal C and ground.
|
8. |
If less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
|
9. |
If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
|
10. |
If all circuits test normal, test or replace the B18 battery current sensor.
|
B1516 66
1. |
Verify that the B18 battery current sensor is installed securely around the negative battery cable, with the tape tab pointing away from the negative terminal on the C1 battery.
|
2. |
If the B18 battery current sensor is not installed correctly, remove and reinstall the sensor properly.
|
3. |
Replace the B18 battery current sensor.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Battery Current Sensor Replacement
|
• |
Control Module References
for BCM replacement, setup, and programming
|