DTC B1529
DTC B1529 |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B1529 03
Control Module Voltage Reference Output 5 Circuit Low Voltage
DTC B1529 07
Control Module Voltage Reference Output 5 Circuit High Voltage
Diagnostic Fault Information |
Electrical DTCs
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
12V Reference
|
B1529 03, B1405 03
|
1
|
B1529 07
|
B1529 07
|
Steering Wheel Control Switch Signal
|
1
|
1
|
B3622 07
|
-
|
1. Steering Wheel Controls Inoperative
|
Circuit/System Description |
The body control module (BCM) supplies voltage to the steering wheel control switches and monitors the return signal. Each switch state is associated to a set resistance value and when pressed a specific voltage drop occurs across the resistor unique to the switch. The BCM identifies the switch selection and activates the feature.
Conditions for Running the DTC |
• |
The system voltage is between 9-16 V.
|
• |
The ignition is ON.
|
Conditions for Setting the DTC |
B1529 03
• |
The BCM detects a short to ground in the 12 V reference circuit.
|
• |
The above condition is present for greater than 30 s.
|
B1529 07
• |
The BCM detects a short to voltage in the 12 V reference circuit.
|
• |
The above condition is present for greater than 30 seconds.
|
Action Taken When the DTC Sets |
The BCM will ignore switch inputs.
Conditions for Clearing the DTC |
• |
The condition responsible for setting the DTC no longer exists.
|
• |
A history DTC will clear once 100 consecutive malfunction free ignition cycles have occurred.
|
Reference Information |
Schematic Reference
Steering Wheel Secondary/Configurable Control Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Steering Wheel Controls Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing |
1. |
Ignition OFF, disconnect the X3 harness connector at the X85 Steering Wheel Air Bag Coil.
|
2. |
Ignition ON, test for greater than 11 V between the voltage reference circuit terminal 6 X3 male side and ground.
|
3. |
If less than the specified value, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
4. |
Test for greater than 11 V between the voltage reference circuit terminal 6 X3 male side and the signal circuit terminal 7 X3 male side.
|
5. |
If less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
6. |
Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module.
|
7. |
Test for infinite resistance between the signal circuit terminal 7 X3 male side at the X85 Steering Wheel Air Bag Coil and ground.
|
8. |
If less than the specified value, test the signal circuit for a short to ground.
|
9. |
If all circuits test normal, test or replace the S70R Steering Wheel Controls Switch - Right.
|
Component Testing |
Static Test
1. |
Disconnect the harness connector at the X85 Steering Wheel Air Bag Coil.
|
2. |
Test the resistance between the terminals 6 X3 female side and 7 X3 female side of the X85 Steering Wheel Air Bag Coil.
|
3. |
If any of the resistance measurements for the individual switches are not within the specified resistance values, replace the S70R Steering Wheel Controls Switch - Right.
|
Function Switch | Minimum Resistance Value | Maximum Resistance Value |
Volume Up
|
1.0 kΩ
|
1.4 kΩ
|
Volume Down
|
1.3 kΩ
|
1.7 kΩ
|
SRC ↑
|
3.4. kΩ
|
4.2 kΩ
|
SRC ↓
|
2.0. kΩ
|
2.8 kΩ
|
Source
|
2.8 kΩ
|
3.2 kΩ
|
Phone/Push to Talk
|
3.6 kΩ
|
4.0 kΩ
|
Hang Up/Audio Mute
|
5.1 kΩ
|
5.5 kΩ
|
No Switch Pressed
|
O.L.
|
O.L.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for BCM replacement, programming, and setup