SAAB WIS ONLINE

DTC B0073

DTC B0073

Diagnostic Instructions


• Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

• Review Strategy Based Diagnosis for an overview of the diagnostic approach.

• Diagnostic Procedure Instructions provides an overview of each diagnostic category


DTC Descriptors

DTC B0073 01

Passenger Seat Belt Switch Circuit Short to Battery

DTC B0073 02

Passenger Seat Belt Switch Circuit Short to Ground

DTC B0073 04

Passenger Seat Belt Switch Circuit Open

DTC B0073 06

Passenger Seat Belt Switch Circuit Low Voltage/Open

DTC B0073 08

Passenger Seat Belt Switch Circuit Performance - Signal Invalid

DTC B0073 0B

Passenger Seat Belt Switch Circuit High Current

DTC B0073 0C

Passenger Seat Belt Switch Circuit Low Current

Diagnostic Fault Information

Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance
Passenger Seat Belt Sensor Control

B0073 02, B0073 0B

B0073 04, B0073 06

B0073 01

B0073 08



Circuit/System Description

The inflatable restraint seat belt buckle switch is within the seat belt buckle and provides an input to the inflatable restraint sensing and diagnostic module (SDM). The SDM supplies a low reference circuit and a seat belt switch signal circuit to determine a buckled or unbuckled condition. The SDM monitors the seat belt switch circuits and if a fault is detected a DTC will be set.

Conditions for Running the DTC

Ignition voltage is between 9-16 V.

Conditions for Setting the DTC

B0073 01

The passenger seat belt switch circuit is shorted to voltage.

B0073 02

The passenger seat belt switch circuit is shorted to ground.

B0073 04

The passenger seat belt switch circuit is open.

B0073 06

The passenger seat belt switch circuit is shorted to ground or open.

B0073 08

The passenger seat belt switch circuit is invalid.

B0073 0B

The passenger seat belt switch circuit is above threshold.

B0073 0B

The passenger seat belt switch circuit is below threshold.

Action Taken When the DTC Sets

The SDM will store a DTC and illuminate the Air Bag indicator in the instrument cluster.

Conditions for Clearing the DTC

The condition responsible for setting the DTC no longer exists.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

SIR System Description and Operation

Electrical Information Reference


• Circuit Testing

• Testing for Intermittent Conditions and Poor Connections

• Wiring Repairs

• Connector Repairs


Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool Driver Seat Belt Status parameter while buckling and unbuckling the seat belt. The reading should be Unbuckled when the seat belt is unbuckled and the reading should be Buckled when the seat belt is buckled.

Circuit/System Testing

Warning

When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.


For additional information about the SIR Precautions refer to SIR Service Precautions .


• Air bag module

• SDM module

• Air bag wiring harness connector

• SDM wiring harness connector



1. Ignition OFF, disconnect the X1 and X2 harness connector at the K36 Inflatable Restraint Sensing and Diagnostic Module and the harness connector at the B88P Seat Belt Switch - Passenger.

2. Ignition ON, test for less than 0.3 V between the B88P Seat Belt Switch - Passenger harness connector terminal 1 and ground.

3. If greater than the specified range, test the circuit for a short to voltage.

4. Test for less than 0.3 V between the B88P Seat Belt Switch - Passenger harness connector terminal 2 and ground.

5. If greater than the specified range, test the circuit for a short to voltage.

6. Ignition OFF, test for infinite resistance between the B88P Seat Belt Switch - Passenger harness connector terminal 1 and ground.

7. If less than the specified value, test the circuit for a short to ground.

8. Test for infinite resistance between the B88P Seat Belt Switch - Passenger harness connector terminal 2 and ground.

9. If less than the specified value, test the circuit for a short to ground.

10. Test for less than 1 Ω between the K36 Inflatable Restraint Sensing and Diagnostic Module harness connector terminal 45 X3 and B88P Seat Belt Switch - Passenger harness connector terminal 1.

11. If greater than the specified range, test the circuit for an open/high resistance.

12. Test for less than 1 Ω between the K36 Inflatable Restraint Sensing and Diagnostic Module harness connector terminal 44 X3i and B88P Seat Belt Switch - Passenger harness connector terminal 2.

13. If greater than the specified range, test the circuit for an open/high resistance.

14. If all circuits test normal, replace the B88P Seat Belt Switch - Passenger. If the DTC resets, replace the K36 Inflatable Restraint Sensing and Diagnostic Module.


Component Testing


Static Test

1. Ignition OFF, disconnect the harness connector at the B88P Seat Belt Switch - Passenger.

2. Test for less than 10 Ω between the B88P Seat Belt Switch - Passenger connector terminal 1 and terminal 2.

3. If greater than the specified value, replace the B88P Seat Belt Switch - Passenger.

4. Fasten the passenger seat belt.

5. Test for more than 200 Ω between the B88P Seat Belt Switch - Passenger connector terminal 1 and terminal 2.

6. If less than the specified value, replace the B88P Seat Belt Switch - Passenger.


Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.


• Driver or Passenger Seat Belt Buckle Replacement

• SIR/SRS Wiring Repairs

• Control Module References for SDM replacement, setup, and programming