DTC B250B
DTC B250B |
Diagnostic Instructions |
• |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
• |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
• |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
DTC Descriptors |
DTC B250B 01
Driver Door Unlatch Low Control Circuit Short to Battery
DTC B250B 02
Driver Door Unlatch Low Control Circuit Short to Ground
Diagnostic Fault Information |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
Driver Exterior Door Lock Switch Signal
|
B2516 02
|
1
|
1
|
-
|
Driver Door Unlatch High Control
|
2
|
2
|
B250B 01
|
-
|
Driver Door Unlatch Low Control
|
B250B 02
|
2
|
B250B 01
|
-
|
1. Door Lock Malfunction
2. Door Latch Malfunction |
Circuit/System Description |
When any exterior door handle is lifted, switched ground signals are sent to the remote control door lock receiver through the door handle switch signal circuits. Upon receipt of these inputs, the remote control door lock receiver will check the door lock status of the following inputs:
• |
Door unlock switch activation
|
• |
Keyless entry unlock command
|
• |
Passive keyless entry unlock command message is received by the remote control door lock receiver
|
Once the enable criteria has been met, the remote control door lock receiver will supply power and ground to door latch control circuits and the door will release.
Conditions for Running the DTC |
Battery voltage is between 9-16 V.
Conditions for Setting the DTC |
B250B 01
The remote control door lock receiver detects a short to battery in the driver door unlatch motor unlatch control low circuit.B250B 02
The remote control door lock receiver detects a short to ground in the driver door unlatch motor unlatch control low circuit.Action Taken When the DTC Sets |
The remote control door lock receiver ignores inputs from the driver exterior door handle switch.
Conditions for Clearing the DTC |
• |
The DTC will be current for as long as the fault is present.
|
• |
When the fault is no longer present, the DTC will be a history DTC.
|
• |
A history DTC will clear after 50 ignition cycles.
|
Reference Information |
Schematic Reference
Door Lock/Indicator Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Power Door Locks Description and Operation
Electrical Information Reference
• |
Circuit Testing
|
• |
Connector Repairs
|
• |
Testing for Intermittent Conditions and Poor Connections
|
• |
Wiring Repairs
|
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification |
Ignition ON, command the body control module Driver Door Unlatch to Unlatch and return to Idle. The driver door latch should Unlatch when commanded.
Circuit/System Testing |
1. |
Ignition OFF, disconnect the harness connector at the A23D Door Latch Assembly - Driver.
|
2. |
Test for less than 10 Ω between the control circuit terminal 10 and ground.
|
3. |
If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K77 Remote Control Door Lock Receiver.
|
4. |
Test for less than 10 Ω between the control circuit terminal 5 and ground.
|
5. |
If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K77 Remote Control Door Lock Receiver.
|
6. |
Connect a test lamp between the control circuit terminals 5 and 10.
|
7. |
Command the Driver Door Unlatch to Unlatch and return to Idle with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
|
8. |
If the test lamp is always OFF during either of the commands, test either control circuit for a short to ground. If the circuits test normal, replace K77 Remote Control Door Lock Receiver.
|
9. |
If all circuits test normal, test or replace the A23D Door Latch Assembly - Driver.
|
Component Testing |
Driver Door Latch Test
1. |
Ignition OFF, disconnect the harness connector at the A23D Door Latch Assembly - Driver.
|
2. |
Install a 15 A fused jumper wire between one of the control terminals and 12 V. Momentarily install a jumper wire between the other control terminal and ground. Reverse the jumper wires at least two times, the door latch should perform the Lock/Unlock functions.
|
3. |
If it does not perform as specified, replace the A23D Door Latch Assembly - Driver.
|
Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• |
Front Side Door Lock Replacement
|
• |
Control Module References
for remote control door lock receiver replacement, setup, and programming
|