SAAB WIS ONLINE

DTC B3205, B3210, B3215, or B3220

DTC B3205, B3210, B3215, or B3220

Diagnostic Instructions


Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Review Strategy Based Diagnosis for an overview of the diagnostic approach.

Diagnostic Procedure Instructions provides an overview of each diagnostic category.


DTC Descriptors

DTC B3205 00

Driver Window Motor Circuit

DTC B3205 39

Driver Window Motor Circuit internal electronic failure

DTC B3205 42

Driver Window Motor Circuit calibration data set not programmed

DTC B3205 4B

Driver Window Motor Circuit calibration not learned

DTC B3210 00

Right Front/Passenger Window Motor Circuit

DTC B3210 39

Right Front/Passenger Window Motor Circuit internal electronic failure

DTC B3210 42

Right Front/Passenger Window Motor Circuit calibration data set not programmed

DTC B3210 4B

Right Front/Passenger Window Motor Circuit calibration not learned

DTC B3215 00

Left Rear Window Motor Circuit

DTC B3215 39

Left Rear Window Motor Circuit internal electronic failure

DTC B3215 42

Left Rear Window Motor Circuit calibration data set not programmed

DTC B3215 4B

Left Rear Window Motor Circuit calibration not learned

DTC B3220 00

Right Rear Window Motor Circuit

DTC B3220 39

Right Rear Window Motor Circuit internal electronic failure

DTC B3220 42

Right Rear Window Motor Circuit calibration data set not programmed

DTC B3220 4B

Right Rear Window Motor Circuit calibration not learned

Circuit/System Description

The BCM monitors, receives and transmits serial data to each of the doors switches and window motors. When a window switch has been activated on the driver window switch, a signal is sent to the BCM which sends a signal to the appropriate window motor and the window motor will move in the direction commanded.

Conditions for Running the DTC


The ignition switch is in the ON position.

Battery voltage must be between 9-16 V.


Conditions for Setting the DTC

B3205 00, B3210 00, B3215 00, B3220 00

The BCM has detected that the compatibility code stored in the affected window motor does not match the compatibility code stored in the BCM.

B3205 39, B3210 39, B3215 39, B3220 39

An internal malfunction has been detected by the BCM in the power window motor while commanding the window UP or DOWN.

B3205 42, B3210 42, B3215 42, B3220 42

The BCM will automatically attempt to download the calibration program into the appropriate window motor (As will occur when the window motor has been replaced), if the first calibration program fails to load, the BCM will attempt to download the calibration program a second time. If this download fails, the BCM will set appropriate DTC.

B3205 4B, B3210 4B, B3215 4B, B3220 4B

The BCM detects that a window motor is "not normalized" which will occur under the following conditions:


When the battery has been disconnected

When the battery has been replaced

When the door wiring harness has been disconnected

When the window motor has been disconnected.


Action Taken When the DTC Sets

B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 39, B3220 39

The affected motor will be inoperative.

B3205 4B, B3210 4B, B3215 4B, B3220 4B

The affected motor will not perform the express up or express down functions and the driver information center will display Open, then Close Driver Window or will display Open, then Close Passenger Window.

Conditions for Clearing the DTC

B3205 00, B3210 00, B3215 00, B3220 00

Installing a compatible window motor for that specific make and model vehicle.

B3205 39, B3210 39, B3215 39, B3220 39

The appropriate window motor must be replaced before the DTC can be cleared.

B3205 42, B3210 42, B3215 42, B3220 42

The appropriate window motor must be replaced before the DTC can be cleared.

B3205 4B, B3210 4B, B3215 4B, B3220 4B

The appropriate window motor must be normalized before the DTC can be cleared.

Reference Information

Schematic Reference

Moveable Window Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Power Windows Description and Operation

Electrical Information Reference


Circuit Testing

Connector Repairs

Testing for Intermittent Conditions and Poor Connections

Wiring Repairs


Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification


B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 00, B3215 39, B3215 42, B3220 00, B3220 39, B3220 42

1. Ignition ON, command the M74 window motor UP and DOWN with a scan tool. The M74 window motor should perform the UP and DOWN functions.

2.
Note

If the window performs the UP and DOWN functions, clear the DTC


Replace the M74 window motor with a M74 window motor compatible for that specific make and model vehicle.


Circuit/System Testing


B3205 4B, B3210 4B, B3215 4B, B3220 4B

1.
Note

The doors must be completely closed prior to normalizing the windows, a door that is open or ajar may cause the power window to function abnormally or it may become inoperative while performing the normalizition procedure. If this occures, verify that the door is completely closed then repeat the normalization procedure.


Ignition ON. Start with the window completely raised. Hold the relevant window switch depressed until the window is completely open. Hold the switch depressed another 5 seconds after the window is completely open.

2. Pull the power window switch up until the window is fully closed and continue holding the switch up for approximately 5 seconds after the window is completely closed.

3. Command the window to express UP and express DOWN by pressing the window switch past the first detent and releasing and then pulling the window switch past the first detent and releasing. The window should perform the express UP and express DOWN functions.

4. If the M74 window motor does not perform as specified and the DTC resets, replace the M74 window motor.


Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.


Front Side Door Window Regulator Motor Replacement

Rear Side Door Window Regulator Motor Replacement

Control Module References for BCM replacement, setup and programming